Search results

I am looking for a complete arbor assembly for a Delta 34-400 10” Table Saw. This would include the carrier assembly, the arbor shaft/spacer/lock nut and bearing retaining ring (threaded). Also, the blade nut and washer. The part number may be 422-03-014-0011. It rotates on a ¾” shaft. Other...

Looking for these two items. I'm restoring this saw and these parts are missing on one hand wheel. I'm trying to keep this all original and peer not to use aftermarket parts. If you have the entire hand wheel shoot me a price. The handle is around 2" long with a 1/4"+ shaft. Thanks, Sub Dude

I have a shop that is around 16 by 20 feet with 10 ft ceilings. I have 7-4ft two bulb hooded florescent fixtures. I purchased a box of bulbs 10 years ago when we built the house. I’ve used all of the bulbs and now I think I had a ballast go bad so I’m down one fixture and I’ve got other bulbs...

I just picked this up today and can't seem to find out much about the model. It says Series 34-770 and the SN is 1791. I am familiar with the Delta Serial numbers and can't figure this one out. The model (or series) 34-770 is hard to find online. I did find a manual that is about the same as...

I introduced this machine recently in the Vintage Craftsman thread and a suggestion was made that I should journal my rebuild. I haven’t done this before since I usually just ask for advice from forums and then move on. I look forward to walking through this process with you. I’ve rebuilt...

I have an 8 year old home with a Bryant Furnace that takes a EXPXXFIL0316 MERV13 16by 25 Filter. I change the filter every 6 months. These filters are getting expensive. Every time I buy I need to just **** it up and hit the buy button. I see them now for $50 to $100 each which is a big hum...

I am tuning up this 24" saw for my nephew. Neither he nor I have any experience with a jig saw. I purchased some 5" plain end 15TPI blades and they cut good with stock that is 1/4" or less. 1/2 and 3/4" thick wood and it is really a slog to feed the board. I have the saw running at the slowest...

I have been working on a vintage Atlas 74 drill press with a replacement motor. I just purchased this and I'm trying to get a few things sorted out. When I purchased the DP the motor had a loud hum but it seem to start and run OK. I just had it apart for bearings and it is not the greatest...

I spotted this in an ad recently and, for what the guy wanted for it, well resistance was futile. I look for 50-60's Craftsman 10" Saws to rebuild. I've done more than a few and they are impressive. Once I got this one home, I did some research. It is actually an 8" that looks an awful lot like...

I just need the chrome handle pictured. Thanks

I'm restoring a Craftsman 10" from around 1952 model 103.27520. Both stop collars are missing. I can see the 45 getting lost but the 90 degree is pretty much captive. Anyway, I need two that will fit a 1/2" Acme thread. I'm sure other machine may have the same collar. I'll need the brass set...

I was at a buddies yesterday and he is an artist that works in wood. He mentioned that he couldn't keep blades on his band saw. I restore old machines and I said I'd give it a look. What I found was this rather new Cman saw that looks to be in decent shape. The tires have perished and fell off...

I'm rebuilding an old table saw and it came with a newish TEFC Grizzly (Emerson) 1 1/2HP motor. After running it a little I thought I'd better take the shroud off and see if I could find the source of some rubbing. What I found is that the retainer for the blade was missing and the fan...

Looking for the parts that always break.;) These are from a mid 50's saw but they were used on a lot of 10" saws. Let me know what you have and a price/condition. Sub

I found that my belt sander has a bad brush and I'm attempting to find a replacement and not having much luck. The original part number is 2-730352-01 It is around .335 square or a little over 5/16" The spring is 1/4" diameter The cap is 17/32" The square brush holder is 11/32" square Try as...

I decided to do a Refresh on my saw and found that someone had been into the arbor before and damage was done. The saw ran well before but it had some issues that I wanted to correct. The model is 103.27270 and the part #s are: 46616 Arbor Shaft 46641 Arbor Flange (pressed on) Other model...

I just picked up a 1983 Delta table saw and this belt was on it. Obviously a replacement but what can you tell me about it? Is a table saw a good application for it? It is very loose and flexible and seems to work fine. Just curious. Sub Dude

I just purchased a mid 80's table saw to restore and I noticed that the far end die cast clamp part is broke. Yup, same as everyone else. I'm sure that many table 10" including possibly a unisaw fence part would work. It clamps a 1 3/8" tube rail. If you have one you care to sell, let me know...

Hello Everyone, I have been restoring old machines for resale for a few years. I have done maybe 20 table saws and a few other items occasionally. I've been looking for a drill press and I found this one an hour away. It seems complete except for the table lock lever. Its a 1948 (motor date)...