Search results

  1. C

    how we solved camera interference

    Sounds like you fixed your problem, if you see it come back you can have a look at what WiFi channel your router is communicating on. On most, you can manually set the channel on the band that the cameras are using (2.4 or 5 Ghz). Need to pick one that wont interfere with the neighbours...
  2. C

    How much do you spend heating your shop/garage?

    Attached garage 450sq ft, heated with baseboards 4000w. Keep it around 12 C (~55F) and turn it up to around 18 C (65F) when I plan to be in there. Added cost about $30 / month for Dec to Feb, so my estimate is just over $100 per year to heat. Ottawa Ontario.
  3. C

    Garbage disposal

    I didn't know garbage disposals were so common. A question more out of curiosity, is compost pickup common in the US? Edit: didnt see this was a bumped old thread. Arg.
  4. C

    Fuel Oil Who Burns It?

    I swapped out oil furnace and hw tank with propane about 7 years ago now. Put in a 1000 gal tank that I get filled once in late summer. First 5 years my heating bills were cut in half compared to oil. Prices have gone up the last few years but still cheaper than oil. And I gained some space...
  5. C

    Sagging ceiling section

    Careful with anything that old, ceiling tiles commonly contained asbestos
  6. C

    Low-yield well solutions?

    That Epp Well looks like an interesting solution, I wonder what the typical cost is. OP did you make any other changes to your setup since your last post?
  7. C

    Programmable wall switch?

    I use a combination of the Intermatic timer for outdoors and a bunch of x10 modules inside to switch Christmas lights. I've thought about getting something more up to date, but meh. This works fine!
  8. C

    Anyone really understand well pump systems?

    I'm not an expert but 75psi seems awfully high for a well pump. Have you sourced a pump yet and checked max ratings? Its been a while since I looked into it, I recall 60 psi was a common max cutoff.
  9. C

    Sink Vent Plumbing

    not to mention sewer gases in the house
  10. C

    Cement and winch

    Sounds like a good idea. I think you would need to consider how high the winch/square tube will extend from the slab, if too high the lever effect could bend the tube at the slab (depending on load and tube size of course).
  11. C

    Framing basement walls

    There was an old article in Fine homebuilding that I followed when doing my basement. Same as what a few folks mentioned - styrofoam direct to the walls, then stud a wall in front of that. You lose a bit of floor space this way but a great method for a basement, and you have room in the walls...
  12. C

    How do you "winterize" a power washer?

    Or if you have a basement and have some extra room, drail the fuel and store it down there.
  13. C

    Garage Opener going bad?

    Went through similar issue a few years back with my genie screw drive. Had to inch up the lift force setting more and more for it to open. More investigation showed it was my 20+ year old garage door - thought it was opening up fine on its own, but on closer investigation, some of the steel...
  14. C

    What is it?

    Ah that explains the fan in the first photo! I was going to ask about that...
  15. C

    Wow, it's been two years!?!?!

    welcome back ! <Enter>
  16. C

    Thinking of getting a new, quieter air compressor for the garage. Replace this 20 year old Craftsman

    Earlier this year I got rid of an older husky upright that would wake the dead, and replaced it with a 2 gal quiet husky. Sits on a shelf now, so I gained some floor space, and man this thing is quiet! I love it. Obviously I dont use a lot of air tools with a 2 gal, but this thing perfectly...
  17. C

    The outhouse/shed floor needs replacement. Suggestions?

    I did a similar thing for a small shed in my yard. posted here : https://www.garagejournal.com/forum/threads/my-seasonal-shed-restoration.369341/ I do like jkuro's idea of tipping it over - that would save a lot of work.
  18. C

    Pavers installed no joint sand yet - worry about rain?

    lol. thanks for the feedback. tarped it all in, will see how much we get in the next few days. Supposed to be dry for 3-4 days after so that will be perfect to get the joint sand (poly) in
  19. C

    Pavers installed no joint sand yet - worry about rain?

    Hi, by end of wednesday should have my 300 sq.ft of new pavers laid. Traditional install, solid base of gravel and then 1" sand. Trouble is there is about 1" rain forecasted for Thursday, likely before I can get the joint sand in. Should I cover the pavers to prevent washing out? I can...
Top Bottom