Search results

  1. T

    Snap-on 1/2" Drive x 36" SN36 Breaker Bar?

    How is the Snap-on 1/2 inch drive, 36 inch long, SN36 breaker bars holding up, anybody managed to bend or break one without using a cheater?
  2. T

    Extra Large Oil Filter Wrench

    Looking for band type oil filter wrench for a 5-7/8" diameter plastic hydraulic filter. All I have found stop a little shy of that diameter, any help appreciated.
  3. T

    Wilton Bullet 300N?

    Does anyone know what the bolt spacing is on a base of a Wilton 300N Bullet vise? This is the 300 vise without a swivel. Thanks.
  4. T

    Morgan 30 Machinist Vise?

    Does anyone have the info or a vise to measure the mounting bolt holes center to center on the side to side spacing on newer production Morgan 30 Machinist Vise without a swivel base?
  5. T

    SK Tools Reward Points?

    Are the SK Tools reward points dead at this point, if not how do you apply them to a order? Still some points showing up on my SK account.
  6. T

    Delete

    Delete.
  7. T

    Vaughan Hammer

    I have ordered Vaughan hammers before, but this one is a little sloppy on the handle/wedge job, not what I expect on a hammer at this price point.
  8. T

    Hobart AirForce Machine Cover?

    Hobart AirForce Plasma Machine Cover? I figure it is a long shot, but does anyone have a picture or know where I can access a picture of the back side of the Hobart AirForce Plasma Machine Cover 770966 for the new AirForce 40i and 27i plasma cutters? Wanting to use it on a different machine...
  9. T

    Promo Code for Fireball Tool

    Promo Code for Fireball Tool? I'm looking for a promo code for a Fireball Tool 12" cast iron Mega welding square for 10% or better. :beer:
  10. T

    Speedglas 9002NC Welding Helmet ?

    Has anyone bit the bullet and bought this helmet or had the opportunity to use it, I would really like to know what you think about it and if is it close to being in the same league as as the 9100 series?
  11. T

    Miller Build Blue Rebate Question.

    Do you need the welder serial number to be listed on the purchase invoice for the rebate to be processed by Miller?
  12. T

    Wera Kraftform Screwdriver Diameter

    (Problem Solved, Disregard) Wera Kraftform Screwdriver Diameter I need the actual diameter of the shaft of a Wera 032001 3 x 80mm Stainless Steel Slotted Screwdriver and a Wera 032020 #0 x 60mm Stainless Steel Phillips Screwdriver. Special application is the reason needing the diameter. They...
  13. T

    Felco Loppers

    Been comparing some heavy duty loppers. I was wondering if anyone had a opinion or experince with the Felco cam action loppers compared to their regular heavy duty loppers. I'm sure the cam action makes for easier cutting, but not sure on their longevity under heavy use. I'm comparing the Felco...
  14. T

    Craftsman Table Saw

    This is a good, heavy table saw with a 10" blade from the late 70's to early 80's. Saw also comes with a molding set. Saw works and cuts very well. It's big and bulky, pickup only.
  15. T

    Miller Thunderbolt XL 225/150 AC-DC

    Welder is gone.
  16. T

    Miller Thunderbolt 210 vs Maxstar 161 S vs ESAB Miniarc 161 LTS SMAW

    What's your comparison opinion on these three stick welders? Smaller physical size difference and 120 V compatibility will make no difference for my use.:headscrat
  17. T

    Little Giant Hand Truck Quality?

    I have been thinking about putting a hand truck in the shop, looks like this Little Giant shovel nose would fill my need. Has anyone recently seen or used a Little Giant, that would mind sharing what they thought of the build quality and the usability of their hand trucks.
  18. T

    Peter Wright Anvil

    SOLD. Peter Wright 0 3 6 (90lb) anvil in good condition, has good rebound and ring.
  19. T

    WTB Table for Clausing 18" Drill Press

    I'm looking for a table in good shape for a Clausing 1800 series drill press. It will be approximately 12"x 14" across the top, with 6 slots and a bore hole. The part number 18-2 should be cast on the bottom of the table.
  20. T

    Chuck Key Compatibility

    Will a Jacobs K3 chuck key work like it should in place of a Rohm S10 drill chuck key? :headscrat
Top Bottom