Search results

Some young person probably needs these. I don’t need them anymore. I was never meant to be a tech. I’m ill now but that’s ok. The person that gets these is very honest. Those that wanted this stuff and decided to be honest understand that this STUFF will help the young person and his or her...

Tool only no dies. Never been used. I will ship in the US. 90.00 Sent from my iPhone using Tapatalk

Cat exhaust stud removal group. 225.00 Shipped to a lower 48 zip code. Sent from my iPhone using Tapatalk

I need to purchase a 1" drive impact over the next few months. I have a IR titanium 3/4 " drive. It's been good, I have rebuilt it a couple of times over the years. No biggie. It still hits hard. The 1" version is basically the same thing with a one inch anvil. I would like to keep the price...

I want to add a KRL7012 to my box. I don’t have a snap-on dealer in my area. Is this something that has to be special ordered? Sent from my iPhone using Tapatalk

This is in new condition as I bought it new and have never used it. I don't need it. I would like to get 400.00 obo I will ship in the lower 48 for that. Sent from my iPhone using Tapatalk

I need a crimp tool like this one here. I do not really want to spend 500.00 on a crimper like this at this time. Any recommendations on an off brand or more frugal version? Sent from my iPhone using Tapatalk

What are these little US made utility carts worth these days? I know it is only worth what you can get for it but what is a starting point? Sent from my iPhone using Tapatalk

I noticed that matco came out with a road box. I suspect the lid hinge is going to be a week point from the looks. Pretty pricy as well.. Be interesting to see how they hold up in real world field work. Sent from my iPhone using Tapatalk

Other than a knife what are you using to strip down 1/0 AWG exane? Budget <200.00

I bought this vice a couple of weeks ago and plan on installing it on a shop cart. I'm just doing a basic clean-up and paint. Not sure the make but it says 6-78 on the stamp. I took one coat of blue, one coat of red and what appears to be original silver/grayish finish off. I went ahead and...

I have had the DCF883 3/8 impact for just a couple of months. I was removing some Morman couplers yesterday and the motor started to smoke and send sparks flying everywhere. Has anyone had this issue? The only reason I went ahead and bought this unit is due to already having some Dewalt 20...

Does anyone have any experience with this Diesel engine rebuild stand? Is it worth the cost? Where did you find the best pricing? Sent from my iPhone using Tapatalk

Ok I acquired a used wood lathe and it has a couple items attached to the bench that I could use some help identifying what they were used for with the lathe? I will add a few photos . The lathe is pretty old but it runs really smooth and it is really solid. This press is attached to the...

Has anyone built a shop cart on casters with this stuff? I'm thinking about building a metal frame to mount these two pin decks to. Mount a ear for a vise, install some tool boxes under the deck. Sent from my iPhone using Tapatalk

My brother and I insulated his tool shed over the holiday and we started putting up 1x8 blue pine rough sewn lumber to finish the walls. I'm wondering what a good indoor sealant to seal it with would be?

So I have a drawer full of HF die grinders along with some older worn out IR stuff. My SOP has always been to use the HF junk until it quits then throw it in the garbage. Don't loose much sleep over that at the price point but the efficiency is really not up to par. I have some major engine...

Well I have had this Echo 550p for a few months and am really liking it. All I have had to do is tune it for elevation so far. It is not to heavy, has good power and does not vibrate to bad.

Ok I have this old 4 foot pipe wrench. The wrench was found with about 6 inches of the end sticking out of the ground. The area where the wrench was found was a gold mining area that saw the majority of it's most active years in the 1890's. Not suggesting that this wrench is from that era...

So I'm trying to get around to organizing and setting up work areas in my garage. I was given some old cabinets that I think I can put to use in my garage. The cabinets are solid and I can easily attach them to the wall. They could use some paint and hardware. I was thinking about milling up...