Search results

Haven't used these in forever so they gotta go. 1st is Young Bros. Letters, 1/4" $55 shipped 2nd is Young Bros. Numbers, 3/16" $30 shipped 3rd is Columbia Marking numbers, 1/4" $45 shipped Shoot me a message to discuss, make offer etc..

Going through more stuff since I don't work in the field anymore and have kids dental procedures to pay for: Got this stuff in a lot I bought years ago when I was in machining school Snap On contour/conforming magnetic base. New/like new(i think i remember trying it out once or twice but i...

Sold

Running an LP line into my hunting blind and have an old pull box to help keep weather out as well as mice and squirrels from chewing around it. 1/2 inch wall plus box, I need a grommet with about 5/8 neck and a hole size around 3/4-7/8 to get the fitting and hose through. Can't seem to find...

Hello! I have a Nu-way propane stove (link at the end) for my deer blind, which is a metal flat roof (pitched a little) with about 3" over hang in the rear. It calls to be vented out the roof, or out the side and above the roof (90 degree out then 90 degree up with a rain cap), to get carbon...

Looking for a new miter saw stand, and can't afford the bosch (that's the cats meow as far as I'm concerned).. I was going to go with the dewalt one with the wheels on the floor, but it gets bad reviews with its cable system getting stuck. Would like to store my 10" dewalt slider on it on its...

ONot a garage but getting my hunting blind plans ready. Doing steel currogated roofing. Got it all figured out except the eave side (flat roof lower pitch). So normally I've seen the felt paper get covered at the edge at the peak and sides with the drip edge, and the felt paper going over the...

Going to be building a large, raised hunting blind this spring. Will have 6x6 posts notched, joists etc.. walls will be plywood. What treated wood sealer do you guys like? Will need to treat the ends of joists, the 6x6 posts, edges of plywood, everything. Obviously it will still need to...

If you didn't catch the ad menards has most of their treated lumber and plywood with a 9 percent rebate... good way to calm some of the high prices if you need it now. On a side note, I purchased 1600 dollars in lumber. For some reason my debit card declined (probably a limit) so I used a...

Going to build a hexagon deer blind. I can either do a hexagon roof or just a square roof to make life easier but I'm wondering about roofing material. I'm pretty handy but know nothing about roofs. It will be a flat roof with enough pitch to run water off... Basically a flat shed roof. I'm...

My driveway was poured like **** and heaves some over winter above my sidewalk line along my house.. id like to get the sidewalk against my foundation lifted some to bring it level with the driveway so the water isn't trapped. It hasn't really settled, they just poured the driveway a little...

Just curious why all pex transition fittings (copper to pex) in the box stores made of brass? Why aren't they made of copper (pictured)? Is it a cost issue? Reliability? I'd like to order some copper fittings for ease of soldering... any downside or good to go? I hate soldering brass... yeah...

Need to replace my water heater soon... its at best guess 16-20 years old (never searched for an install date) Going to do this myself, my first one but it seems straight forward... just 2 questions. 1.what is this on my water line? The right side my main cold lime comes in, the left side it...

I got a swisher 44" finish mower. Has a 10.5 briggs IC. Picked it up, needed some TLC. Basic maintenance and was missing the recoil starter. Got a new recoil, got it started. Hit a slightly hard wall some times when trying to start it but it was definitely never smooth pulling all the way...

Sold

Sold Sold

I'm guessing the answer is yes.. but I HATE the newer brass sweat fittings and always give me a fit. Ive never (knock on wood) had a copper fitting leaked that i sweated. I am installing new whole house filters and want to do it in pex (I'm switching the house to pex eventually as I go) So...

Is it me, or do I get less in speed perks dollars now? I havent read into it very much... is this new program better or worse?

Gonna give a go at compounding my wifes car and my truck with meguiars ultimate compound and ultimate polish, followed by using the polisher to apply the wax as well. Looking for some cheap pads, haven't buffed a vehicle since I was a teenager so I dont want to go all out until I get the feel...

I know this is a deals area.. but when I need to find a deal you fine folks at GJ are on top of it. Looking at a truxedo lo pro, I have an 11 f150 with 6.5 bed, would consider a standard truxport if I cant get a lo pro at a good price. Didnt know if anyone has a coupon to anywhere? Best I can...