Search results

So it's time for a new jack my harbor freight grey low profile jack finally died I was wondering how the new orange jacks compared to the previous generation grey jacks For the orange jacks vs grey jacks Are they built better? Better pumps? etc etc

HI everyone one my girlfriends dad found this and was wondering what the he'll is it lol

Just a got a 20 gallons parts washer and I'm going to be using water based solvent....and I want to heat up the solution was wondering in anyone used a magnetic engine block heater to heat up their tank and how effective it would be Please reply back thanks

Hi I have a 20 ton air hydraulic shop press and seeing what everyone recommends as far as what size bearing splitter to use to remove the stuck inner race on wheel hubs Please reply back thanks

Looks like the copper pipe is leaking and also is 1/2 it's supposed to be 3/4. So would I be able to use galvanized pipe to connect the pump to the air tank?

My air compressor losses 5psi after it shuts off at 175psi? Trying to see if this is normal my air compressor shuts off at 175psi and drops down to 170psi right after What could it be?

Just bought a new pressure switch its comes factory with it turning on @145psi and turning off at 175psi So I install it and looks like its about 5psi too low....turns on at 140psi and turns off at 170psi... Should I adjust it or leave it alone?

so I bought a Campbell Hausfeld tf series pump which has a Centrifugal Unloader Valve and it is leaking air when the pump is running Is that normal? Also it is really slow to build up pressure like 20 minutes just to get to 100psi.

Hi was wondering what you all think? Currently have a 5hp spl 18 amp motor 3440 rpm Was looking to get a true 3hp 1740 rpm motor.. What would be the advantages or disadvantages?

Ok i see where the motor connects to the black, white and ground....but on the ends where the reds wires are is what throws me off....where do I attached the black and white wire on the ends where the red wires are?

Ok i see where the motor connects to the black, white and ground....but on the ends where the reds wires are is what throws me off....where do I attached the black and white wire on the ends where the red wires are?

HI im trying to figure out which of these compressor motors I can run on my 220v 20amp circuit breaker Here's the breaker in the attachment motor # 1 Leeson 131534 3 HP 1740rpm Single phase http://www.leeson.com/leeson/searchp...0&productType= motor # 2 WEG Compressor Duty Electric Motor...

HI im trying to figure out which of these compressor motors I can run on my 220v 20amp circuit breaker Here's the breaker in the attachment motor # 1 Leeson 131534 3 HP 1740rpm Single phase http://www.leeson.com/leeson/searchproduct.do?invoke=viewProductDetails&motorNo=131534.00&productType=...

This an smc -sanborn manufacturing company 1978 60 gallon

Looking for some reviews on this... I currently running a Central Pneumatic Earthquake 1/2" impact wrench from harbor freight Please reply back thanks

Hi my girlfriend bought this at a garage sale....What is it?

Hi I was wondering who makes the matco SCPMTW36V 1/2" DRIVE 3 PIECE WHEEL NUT http://www.matcotools.com/catalog/product/SCPMTW36V/1-2-drive-3-piece-wheel-nut-protector/ And the Mactools SVPT116B 11-PC. Impact Socket Wheel/Lug Protector Set...

Looking to buy a 1/2" cordless impact...what does everybody recommend? This is what im looking at now http://www.craftsman.com/craftsman-c3-189-8221-heavy-duty-impact-wrench-kit/p-00945195000P

Looking into purchasing some of these please reply back thanks

Looking for input on these brands....would they stand up for professional use? Currently my tool collection is Snap-on, Mactools and Matco