Search results

I picked these up recently. They are 14" long, 1 1/4 tall and .065 thick. Apex and Karflex brand. How old are these? Were they used on a regular hack saw or are they some kind of industrial blade? Thanks for any info.

I have always bought cheep Menards house brand oscillating saw blades. They work ok but I am doing some cutting on wood that has hidden nails in it. These blades are pretty much done as soon as you hit a nail with them. Are the better blades able to withstand hitting a nail or do they go...

I am trying to check if it is the battery or the charger that is bad. I can get decent reading on the battery but when I test the charger with a multi meter it doesn't work. I have other brands of batteries and chargers and they do the same thing, batteries check out fine but not the chargers? I...

Anyone know what this is. I have a few of them in different sizes. There is supposed to be a o ring in the groove I marked in red.

I am looking at an old Smith 100 pull behind air compressor. It has a 302 Ford engine on it. It runs on one bank of cylinders and the other compresses the air. I have always wondered how they keep in balance? Anyone know?

I have 150 psi in my air tank but I can only get 110 through the regulator. I have tried two different regulators and 2 different gauges. Both regulators are 3/4" in and out. Any ideas? thanks

Anyone know what this is? It was with a tool lot I bought.

Anyone know what makes the spark on these? The problem is no spark in the lower circled area.

I have a Whitney #11 rotary punch. I am having no luck finding punches and dies for it. I have seen some that are similiar but not the right ones. Here is a rough sketch (excuse the art work, not my specialty). Measurements are close using a cheap caliper. Any ideas? Thanks

I have this old greaser that I want to get cleaned up and painted. I can't get the pump out of the tank. It spins, I tried turning certain ways in case it is keyed. I have not reached inside yet to feel for a nut or whatever. Any ideas?

I have had this for 20 years and have never changed a punch in it. Does anyone know if the nut holding the punch is left or right hand thread? It is kind of boogered up and the wrench slides off it. I may end up cutting it off. Also does anyone know what other models fit it? Thanks

Does anyone know what this is?

Vintage Williams sockets. Everything in pics. $25.00 shipped to lower 48. Paypal, cross posted.

I have searched but can not find info on installing a overhead garaged door on a grain bin. I found a few pics but nothing that was of any help. Has anyone on here done this?

Last year I saw a thread (I think it was on here) about renting a rapid air tubing straightener. I bought one and am done with it. Any interest in starting a rental for it. Maybe $25 flat fee and you keep it for a month. After the 6th rental that person keeps owns it and he can now be the one...

Not sure if this is the right place to post this but figured there was plenty of knowledgeable people here. I am replacing oil seals on my pallet jack. One of them is marked 35-47-7/9. I know it is 35MM id, 47 od but what does that 7/9 mean? Does that mean it can be anywhere between 7 and 9mm...

My regulator says it only regulates 10-125 psi. Does that mean if there is 300 psi going into it the most it will ever put out is 125?

So I tried makeing a tube straightener. The rollers I used were too small, the edges of them deformed the tubing. Probably would have worked ok as it would be straightenned out when you use the champhering tool. I know it should have had another roller on bottom, I bought 8 of them and somehow...

Someone in another forum said that if you run your air hoses slightly uphill that you won't get water in the lines. I have never heard this before and don't think I believe it. Opinions?

I am adding a air dryer to my compressor. I have 3/4 copper at the dryer to make the bypass and connections similiar to the one in pic. I would like to test it before hooking it to compressor. I can find expandable plugs to block ends off but how can I pressurize it and put a gauge in so I can...