Search results

Are these torch sets any good? Just need something for occasional cutting and heating. https://www.lowes.com/pd/Lincoln-Electric-Oxygen-Welding-Cutting-and-Brazing-Kit/1000172775

I have been running a dehumidifier in my garage since building it a few years ago. Really helps when a wet vehicle is pulled in there and seem to help keep tools in better shape. I am on my third unit in this time frame, they have replaced it twice and now it is out again. Any decently...

Got a roof that is faded. Anyone use any of the elastomeric coating? Everything I read says 2 coats required. Roofing guy quoted $1100 for a 24x30 building.

Anyone used one of these...

What would a good tough finish be for plywood. Redoing a small older bench and putting a piece of plywood on it to smooth out the old 2x boards. Probably will put a bench top drill press on it and general use otherwise. Considering spraying it with some bed liner spray. Thoughts or suggestions?

Suggestions on cleaning up and painting this old box. I guess originally is was the gray with red drawers. Thought about a solid red or even one of the gray hammered paint finishes. I have a Mac box in the shop also so thought red to halfway match it. Doesn’t have to be a perfect finish.

Which is the best? Talking about walk in doors and it will get a lot of afternoon sun.

Never heard of this brand that Menards sells. https://www.menards.com/main/heating-cooling/air-conditioners-accessories/soleus-air-reg-18-000-btu-208-230-volt-window-air-conditioner/wm1-18e-01-02/p-1479280788834-c-1497103338431.htm?tid=7480595371137618055&&ipos=1 They are cheaper that GE and...

Are these a decent vise? Been watching for a good older vise with no luck. About ready to give up.

What caster material is least likely to flat spot other than steel? Would these be ok? https://m.northerntool.com/shop/tools/product_200660424_200660424 Read somewhere that material was less likely to flat spot.

I think 1/8” metal top. 6’ x 3’. He is asking $150.

Thinking of putting some of this shelving in, basically a 2 foot deep, 8 foot wide and 8 foot tall unit. Thinking of the first shelf 2 feet up and then every 2 feet to the top, so I can roll stuff under it. My questions are: How sturdy are these? Does it have to be bolted to the floor? I may...

I have wanted a code reader for a little while and have some gift cards I can use. Anyone have one of these? Thoughts?

Looking to add some floodlights to the garage. Some I have used in the past seem to have trouble with the sensors. These will be high up and want them to be dependable. I prefer something I can replace bulbs in, maybe something I can put LED floodlight bulbs in.

Wanted to get a couple fans put up to help pull some heat down. I thought about one with a remote just so that I can do less wiring. Looked at these too fans and the is a large difference in their rated CFM of air movement. I wonder if the Canarm is not realistically rated. What would you...

Anyone have any knowledge of this air hose? https://www.autozone.com/air-tools-and-accessories/air-hose-and-reel/vaper-3-8-in-x-50-ft-hybrid-air-hose/977898_0_0 No reviews on their site. Had some gift cards to spend and need an air hose. Should I spend them on something else?

I am putting foam between my girders and wanted to cover the walls. Would the OSB give any problems as they are about 3 feet apart? I did not want the OSB to bow between the girders. Mainly just want something to cover the foam.

Has anyone tried one of these: https://www.samsclub.com/sams/honeywell-6000-lumen-led-rectangular-wall-pack-security-light/prod21480079.ip?xid=plp_product_1_2

Does anyone have any knowledge about water based epoxy? I have the opportunity to get some at a discount and wondered how good it will hold up in a garage. Looking for an easy to apply product with minimal prep. They say this is a good choice. This is the product...

What do you all feel is fair on pricing tools that are still made? For example say a power tool can be bought new at Lowes for $200, what is fair to ask for a like new tool? Same exact tool. I have my thoughts but it always seems like when I am buying they want new price and when I am selling...