Search results

Hi All, WTB Snapon 1/4 flex sockets thsnka Ray

Hi All, Everything listed bundled Need room! SAE wrench set (not full set) $200 for everything + shipping Screwdrivers Crescent wrenches

Hi All, These are generally good - very good condition. The box / open ended set consists of: 1 1/4, 1 1/8, 1 1/16, 1, 15/16, 11/16, 5/8, 9/16, 7/16, 1/2, 3/8 along with a small collection of misc. $100 + shipping

Sold Like new Punch & Chisel set (like new very good condition, not sure if it was ever used). Comes with tool roll. $40 + shipping

Hi All, I just acquired a older Rigid horizontal band saw model # 945 and am looking for some documentation on it. This is a beast, cast top as opposed to sheet metal. Pretty sure it is a US made Emerson model, but older. Any information would be welcome! Thanks Ray

Hi All, I need to drill 16 1" x 1" holes in concerete. I would REALLY like flat bottom holes and somewhat clean sides. What should I use for a drill & bit. I would prefer to not buy a SDS drill if possible. Thanks Ray

Hi All, My Dewalt impact driver has been great up to recently. Now it seems to be down on power. Granted we are talking about bolts that are torqued to ~ 350lb-ft, but these used to be a no-brainer, and now a real challenge... Is there anything I should look at? Thanks Ray

It would be enormously helpful if there was such a critter... Ray

Hi All, I am looking at a Snap on set: KRM 274 side box, top kr537b, middle kr547, bottom kr557b. They look to be clean, at least the pictures are. They are old, but then so am I :). They have slides, on of them is the 65th anniversary model What is a 'good' or reasonable price to pay for...

Hi All, What I am trying to decide is if I want to get another side box and sell off the top box and use the boxes as a work bench. I can't currently do that because I have a top box. My existing side box is a KR1010 - arguably SO's finest boxes :-) I like that box but would prefer a...

Hi All, I have a Milwaukee bandsaw mounted on the Milwaukee table and I can't seem to get it to cut in a straight line. I have adjusted the arm - the 2 Allen head bolts that allow you to rotate the head. I am cutting 1" square tubing - thick wall stuff, and the blade seems to always kick out to...

I need to rebuild the pump TIA Ray

Sold Thanks

I an curious, they seem good but $$$ Thanks Ray

Screw on type Thanks Ray

Hi All, Been in the market for one. I see Harbor Freight, Torin, Dayton, all look the same. Dayton seems to be made in Taiwan, some others in China. Is there any real difference in quality between the various 10 to units or are they all the same? Is the Granger / Zoro really worth 2x the HF...

Prefer NOT HF / NT - the Chinese stuff or other equally disposable stuff. I don't mind needing to rebuild a cylinder... Thanks Ray

Hi All, Can anyone tell me about the KR292A - bearing or sliders for drawer, etc? I am looking for a PDF Snap-On catalog circa 1990. Would anyone have one to share? Thanks Ray

Hi All, Or perhaps me! It has been some number of years since I last did any welding, and even then I never did much! I have a Millermatic 211, running @220v, .035 solid core wire, 75/25 gas. I am welding steel 16ga square tubing. My settings are right where the welder suggests, the wire...

Hi All, I have a new to me Saylor-Beall 5hp compressor. I fired it up and saw that the pressure cut-off switch is set for ~125psi. seems a bit low. My previous compressor would shut off ~155psi. What is considered typical? Thanks Ray