Search results

Trying to add covers to some aluminum seats I recently built. I'm after minimal padding, and hoping to go from a bare seat to something with a simple cushion design. Black leather would be great, but Vinyl could work. I may go with a houndstooth fabric for the center sections. I've used...

sold

Purchased from my local paint supplier for $675.00 2 months ago. I've since learned a high volume painter buys paint at 50% my walk in off the street DIY cost, so having someone paint my new shop is a few hundred bucks more expensive than me doing it myself. Needless to say, this sprayer is...

Excess to my needs, I'm selling a previously restored Parker 3x vise. Jaws are approx 4 3/4 wide. Opens to 8 inches or so. 75+ lbs, so likely not ideal to ship. Located in the Boston, MA area. $225.00 obo

Anyone have a suggestion for metal (brass/stainless/aluminum) fittings that are compatible with rapid air 3/4 hardpipe? Piping is powder coated aluminum tube. I have not yet confirmed the OD of their three-quarter inch tubing. I’m running a compressed air drop into a space that does not...

REVISED PRICE: $600 obo This thing rips! 2hp 20” disc sander. New SINGLE PHASE 2.0 HP motor installed. 1740RPM, 240 volts. Used exclusively in my wood shop, but works incredibly well on metal with the right sandpaper. Very hard to find with a single phase motor and also in this great of...

Price $500.00 Incredible 1/2 steel welding and fabrication table. 6'x11' in size. About 1400 lbs in steel plate top alone. Top is blanchard ground 1/2 plate on 3"X3" legs. Height off the ground is about 30 inches. Top has surface rust after transporting in the rain, but cleans up with a flap...

Some of you may recall the debacle that my underground garage build became. (builder built the walls too short) I'm now after insurance advice on the off chance anyone here is in the business. Short version is my General Contractor did a poor job on the garage that they built for me. It is a...

I'm neck deep in an extensive underground garage build. It required blasting tons of rock to ultimately allow an entirely undergoing garage to be built into the hillside of my home. Architect designed, this was not an insignificant job as it will total well into 6 figures. Problem is the...

I just won an asymetrical 9k 2 post lift. https://www.naautoequipment.com/UNI-9KAC-9K-Autolift-p/uni-9kac-9k-autolift.htm I plan on installing it in my 27 foot deep bay. I would like to keep it as close to the door as possible since the back wall is covered in workbenches and I'm trying to...

I'm about to install 12 LED ceiling lights. Each light draws 175watts of power. 2100 watts total. at 120 volts this is a 17.5 amp draw. Can I install them on a single 20 amp circuit? The lighting circuit is presently 12 gauge wire protected by a 20 amp breaker. I though there was something...

I'm neck deep in a 400 amp service upgrade that will go from the pole, to an outdoor meter socket with a pair of 200a disconnects/breakers (one to my home panel, and the other to the shop panel) This is being handled by an electrical contractor and is permitted work in cooperation with my town...

Ramsets for overhead mounting I need to mount a dozen lights to the concrete ceiling of a garage. The lights are designed for flush mounting to the ceil in with EMT entering the side of each. (They don't necessarily need to mount to ceiling boxes). Lights weigh 3-4 lbs. Can I use powder...

I'm looking to add a natural gas heater to my 2 car daily driver grage. It will require a horizontal vent. Ordinarily I would use a HotDawg type heater, but because of the layout the vent will be very visible form the street. I wish to avoid the usual hotdawg type III vent style that sticks...

All, I just scored 20 of these Home Depot commercial electric 18,000 lumen 2x1 foot lights for an absurdly low price. https://images.homedepot-static.com/catalog/pdfImages/d8/d8814a2e-679d-45cd-ac6b-9d8c7c7b513c.pdf I would like to install these in my soon to be built 30x35 garage (13 foot...

I'm soon to install 12 LED high bay lights in three rows of 4. Each fixture draws 170 watts (17 amps total draw) so I will break them into 2 "banks" of lights as opposed to using a 20 amp switch. This works well for the layout of my shop. I plan on wiring the 0-10v dimming circuit for these...

I'm building a below grade shop (think walkout basement) of poured concrete and concrete slab roof. Think of it as a walkout basement. There will not be any windows or skylights, so I want to keep the space as bright as possible. Ideally the walls will be white. Can anyone suggest the best...

I'm kicking off a new garage build totaling about 1000 sq/ft. Ceilings are 14 ft, so about 14000 cubic feet in volume. It is essentially a walkout basement with three walls (and roof) buried, and one wall opening to the outside with garage doors. Since this will be below grade and without...

I'm kicking off a new garage build totaling about 1000 sq/ft. This will be below grade and without windows/skylights, so keeping it bright is important. This is a hobby shop with automotive and woodworking. I would like to do a while polyurea floor for light reflection, costs and...

I'm finishing up a new shop that is built into the hillside of my home. It is essential a daylight poured foundation with concrete roof. With the exception of the garage doors the entire thing will be underground. This will be a Fab shop for me, do I'm going densifier on the floor to keep...