Search results

Thanks. Just need to make sure it won't mess with the spacing on the racedeck.

The black looks great. Thanks for the idea.

I am trying “clean up” my base area on one side of my garage. The right side was easy but the left has low block foundation wider than the wall. I was tempted just to paint it and then glue a qtr round to the block to cover the gap. Or had thought about adding wood base with a 90 degree...

This is what I bought. I’m pretty sure it was from Racdeck but it’s been a while. I glued it to the concrete. It has come loose occasionally, but I just glue it again. It just overlaps slightly.

What about a tile that looks like wood. I did the back area of my garage that is for wood working. Doesn't have your typical wood issues and they are pretty decent looking now.

I ordered a 4" rubber transition piece. It comes in a 12' section. I will post pics once I get it. Only ordered for 1 side and will decide if I am doing it on both sides.

Thanks Jennifer helped me out.

Ran into a small problem when installing my race deck. I have a 2 bay garage with 2 separate doors. 1 door sits 5" back from the other. It was an addition done years ago. I had bought the edging pieces, but I need to cut a tile for one of the doors, and that leaves no way to interlock the...

I know this is an older thread, but I had a question on installing the vinyl. I just ordered my vinyl. Did you use a soapy water solution while installing to allow some adjustment, or did you do it dry? The garage looks great. Thanks for all the info.

Mark Your cost should be pretty close to that. There are many different options that are similar to the ultra flex and each contractor has their favorites. They are latex/fortified and have a "flex" bond. I would look at the different costs. Also, the Mapei rep mentioned the Ultra Flex...

If you are using a 12x12 tile over concrete, you would be in good shape with using Mapei's Ultra Flex II. If you want a slightly better bond, you could use their Ultra Flex LFT. It is made for larger tiles, but does also have a slightly better bond. K/K, (for what it's worth), is overkill in...

I know this older, but had a couple of questions, if you see this and don't mind. Thanks for all the detailed info on this thread. When installing the lights, do they just sit on the 2x2's you installed, or do they need to be attached somehow? On the openings on the drywall, did you put a...

Looks great! What racks did you go with for tire storage? Thanks

Great build. Love it, and I am going to steal a few ideas. I was wondering what the depth of the cabinets ended up being? I looked through but didn't see the measurement. Thanks

I am planning on mounting my compressor in my shed and then running lines to the garage for the air. I have been looking at the Maxline and like the idea, but I was concerned about not being able to put a drain at the lowest point of the run. I have seen the setups with the black steel pipe...

I had the circle track with an older lab and she had no problem when wet. No experience with the free flow, but I would think it would be even safer.

I used that a couple of years back and wasn't impressed. It didn't hold up well and the finish wasn't very nice looking. Scratched very easily I did all of the prep work correctly. It also seemed very "thin" to me. More of a paint than a epoxy or coating. If you do use it, make sure to...

I also used the free flow right over the drains in my garage. The slope is very slight, so there isn't any problems with it. I will try and post some pics soon.

I am going to write up a thread on my dealings with buying the lift, but overall it was pretty much a an unpleasant experience to deal with them. I guess if you don't need anything from them other than ordering, they would be fine. It seems to be when there is an issue, that's when the problem...

So I bought an Atlas BP9000. After getting the columns mounted, we noticed that one of the mounting plates on the carriage had been flipped and welded incorrectly while being made. So I contacted the dealer and let them know of the problem. The sent out a new carriage. Upon looking at this...