Search results

<<<As in: Fe3O4 + 8H+ --> 3Fe + 4H2O.>>> I knew somebody would say that....:bounce:

Oh yea.... you will love this thing! Some of the instructions will seem to **** at times but everyone lives through it. I found that I read too fast sometimes as I thought I new what they were saying. A slight bit of difference in wording once in a while makes a difference, and slow reading or...

The XPR-10A set up in wide configuration is what I have. It has been perfect with zero regrets. I studied and studied, just as you, before I finally ordered it. I did the right thing for me and I think you will enjoy yours too. I filled mine with Dexron ATF...that was another thread here on this...

I'm getting my good out of this too..just ordered the screen, and a new gun while I was at it. I use Dollar general muffin pans and square cake pans for misc..will be getting a hand sifter or two as well. Thanks all...........

I have the normal HF cabinet blaster...the larger version, free standing on legs. I have it working well except for clogging the spray gun with paint flakes and chips blasted off of painted, rusted items. Large flakes of paint go up the intake and clog the nozzle. I'm thinking I need a framed...

I hate those drive around scissor lifts... they shake, wiggle, and try to kill me if over 10 ft high..... I pay for anything over 10ft if my boys aren't home to do it for me.

When I put my Bendpak 10K asy up, I checked some of our cars for CG using a floor jack. I would jack each one up a few times until it balanced on the floor jack, then put a piece of tape on the door. I wanted this tape to line up with the post ( or center of the lift plate ) so that the load was...

Wizards picture tells it all. You must drop one side of the bead down and in so the side you are taking off has room to come up and over the wheel. As some of you have said, chasing these little tires around is a lot harder than when working with larger ones...here is the best deal going. I...

Old bed springs pulled with garden tractor or quad... I've done this for years, but he pallet sounds like it should work also...either are free with the old springs a bit harder to find now days. I have heavier equip but is not needed to relocate gravel. Dragging looks real nice when done.

I like those... I threw out the little light that came with my cabinet and bought a pair of Harbor Freight driving lights and mounted them much as yours are. They are 55W H3 bulbs and light things up nicely. I got by for right at 10 bucks and got to stay with 12volt system. I didn't want high...

I agree... nice shelf, well done. My locks work smoothly and fully. About time to check and clean everything, so will be looking for any rubbing etc.

Tony, Mine is exactly like yours. I did not even notice that the cable has this slight angle. It works perfectly fine as it is. Once the cable is on and adjusted you will never notice...I know I did not. : ) Good job at paying attention! Randy

Tony, My books are out in the shop as well, but will look for you. Your towers are set exactly like mine in the first pic of this thread? The top plate stays the same no matter which side the pump is mounted. It should make no difference on the saftey latch cable as to either as I recall...

Too late tonight to go out and look at mine, will look early in the morn as I don't recall any issue... 9 pm Randy

Mine is a metal building type shop.. if you want air condioning you open the door.. : ) but I like it! Would be happy to show you my Bendpak lift if that is anything you may be interested in. I'm not far off...work in Topeka and live 7 mile west in Silver Lake area. colder than heck right now...

I also have one Battery Tender, one big charger with 50 amp boost, and 2 of the HF units. The HF units do not have the circuitry to maintain,,they work but you have to treat them as a trickle charger,,and they both run hot to the touch. Battery tender is excellent product, but are not...

I've had this one for about 1 year now... I love it! The last one was a Schumacher (sp ) it was a piece of c-ap... a waste of money for sure. Read reviews to find a new one and found this one you are looking at...fantastic. I use it to maintain my truck that is stored in my shop building and...

There is no conflict on the saftey latchs, cables, or pulleys...no matter which side you set the control unit. They fit perfect either way. The one thing, and only thing, is the wire to the overhead saftey switch needs to be lengthened. I forget the gauge of the wire offhand ( maybe 16?? )...

Each floor plate is 21" wide, the space between the floor plates is 103 1/16,. This adds up to 145 1/16 total width to the outside of the floor plates. Set like that...it leaves you with 106" between the upright posts.....no to the inside of the platesm, which is the 103 1/16. You have 106...

Are you doing the wide configuration??? Page 4 of the download manual that Steevo posted shows the measurements. I would measure inside to inside without all the squaring sticks. Just use a tape measure......... I think it said 103 1/16 on page 4 for the wide setup.... read it for yourself to...