Search results

Will there be schematics for wiring with the bulbs? I ordered 56 bulbs. How long do they normally last?

I read that, but still don't understand if I need single ended or double ended, etc. Will my tombstones work??

I have a 36 X 30 X14 shop that needs relamped. I currently have 28 dual 4' T8 fixtures in four rows of six. two fixtures over my work bench and two fixtures over my tool boxes, etc. I would like to replace the T8s with LED bulbs. But don't know what I need. The fixtures are powered from one...

I do have a 30# PRV on the floor side and a high PRV on the DHW hot outlet. Instructions read to provide 40PSI minimum to make-up and DHW side. Yes it seems to be running between 10-15PSI, floor side that is.

Thanks Truckman. We got it going today. Exactly what we did.

Well, my radiant floor heat has been in service for almost 5 years now. It has performed very well with 40 gal water heater, with a few exceptions. 1. Below 15*F the water heater fires 24/7 and still has a hard time mantaining a set point of 62* air temp in shop. Usually it sags the set point...

No one has installed a Navien NCB 210, huh? Is this a new company or new model?

I just installed a NCB -210 in my garage hydromic heating system. Everything seems to be working but it won't turn on when my circ pump turns on. I thought it was an on-demand type device. Do I need to wire in a curcuit that tells it the circ pump is on? I can flip a dip switch and make it...

Thanks guys for the suggestions. The Fernco seal looks like the hot setup, I will try to find one to have on hand. I set a level across the sewer flange and found that the stool was touching on the front lip and setting on the flange. Causing it to be able to rock side to side. I cut two...

I know this isn't really about garages but it is in my garage shop. Evidently when they poured the floor around the sewer pipe and sewer flange, they got the pipe higher than the rest of the floor. when I tighten down the toilet hold down bolts the toilet rocks from side to side when you set...

I'm just wanting to control my circulation pump which I think on high speed it still draws less than 1A.

I'm needing a timer that when power is applied, it will close for 15 minutes, then open for 35minutes, then start over, 15 on then 35 off and do this till power is removed. Any suggestions?

Thanks for all the info guys. I passed on it as I had to buy it soon or it was going to be sold to someone else. I did offer him $1200, but he wouldn't take it. I guess I missed a good deal, but not knowing all the above I was a bit leary to buy it. Thanks again.

Yes it looks just like that only the colors are different.

I seen it with my own eyes. That is what it says on the side panels and the power panel. It has a 20A, 30A and a 50A recepticle.

Can parts be found for these generators? That and durability are my major concerns.

It is a wheeled/portable model. I think it's says Guardian, on it. It has a 10 gallon fuel tank for gasoline.

I have a chance to buy a 15000KW Generac generator new, never used, never had gas in it till today. I don't know who or where the engine is made. The generator unit has a tag on it that says, made in the USA. but I can fing nothing that suggest where the 30hp engine is made?? the engine...

The story goes, they use to sell dogs at the Rutledge Flea market, all kinds of dogs, mostly **** dogs and other hunting dogs, but all kinds would be sold or traded there. The Humane Society complained and the state or someone made them stop the commerce in dogs. So then you could buy just...

Thanks guys, I'll check out and consider all the ideas above. We have considered repiping the entire house, but not now.