Search results

Dude I wish I had your energy. Looks like you are making headway. 72 moose plow plastic wear bar This is a link to were I ordered my wear bar for the Moose plow on my Rhino. I wasn't sure how you were going to mount the jacks but now I see! Veddy nice.

Nice sander. I have to relocate the jack on my trailer cause my spare tire on my jeep hits the crank handle. I am going to put a plate and or angle iron between the frame rails. what is the weight rating on your jack? My trailer is only rate for 3000lb and it weighs about 1000. I put a...

Hey, Superman, I read most of this tread , gonna come back later and finish. Kudos to you sir!

I started my collection with the 18V LI-Ion 1/4" impact driver, about a 2 years ago. It came with 1 battery and a coupon for a 2nd free battery. This thing has balls. Right out of the box I put a 3/8" x 6" lag into a rough cut 2x4. Then I registered and charged the battery. Since then I...

Pittsburgh Joe Also ripped off "pants N'at" from a Pittsburgh , pa radio station; WDVE. You go boi'

:thumbup::thumbup:

I just use the parts washer (safety-kleen). But DO NOT soak them. Just use a shop rag dampened with it. Don't know if matters, but i have managed to pull the handles off ALL my ratchets. Had them replaced by the dealer several times. Gave up and now I just buy the normal chrome handles...

Just thought i would mention, what to do if you get flashed!! I am not a welder by trade, but have walked through our weld shop on more than one occasion and been flashed. Didnt know it til I woke up at 3 am feeling like i had 2 handfuls of sand in my eyes. One of our welders told me, if I...

Welcome aboard. The addiction of this site is normal. We all went through it. Its fine. We are family here. BTW. This shop is open 24-7. Enjoy the ride. Good Luck.

2 Thumbs up from the Gluckster. :thumbup: :thumbup:

I have actually broken 2 "cheapy" bars. one, the pin and the other, right at the square drive. BUT, these are old, say 20 years or better. I believe the quality of HF to have improved cosiderably since then. BTW. I ground the "U" shaped end on my broken one to somewhat of a hook, and use it...

I would caution against the HF. I broke 2 pittsburgh breaker bars. And twisted 1 craftsman. I finally bit the bullet and bought a SO long handled 1/2" bar. then the long handled flex head ratchet, 24" i believe. I quit buying the comfort grip handles on ratchets cause I kept pulling the...

Dont know about 12 step, but can I recomend 12 volt.......................

I have the HF TOP and Bottom and the side locker. I didnt really judge the locker quality, cause it is essentially the same quality as the boxes. I installed a magnetic cabinet latch on mine to keep the door closed. It has hooks on both sides and bolt holes. can be mounted on the right or...

there is a used tank dealer not far from me. they are located in perryopolis, pa. i dont rememebr the name off hand but i will be going by there tomorrow and will look to see if i can find a number for ya

Just saw this. http://pittsburgh.craigslist.org/tls/2697810722.html South of Pittsburgh, PA. GO PENS!!!!!!!!!!!

I have the HF 42" top and bottom. After I got mine 2 other guys bought the top and bottom and the 2 side cars. Had to take them out of the boxes to fit them all in my truck at one time. I just added the side locker a few months ago. I agree that they should be deeper. But solid built and...

i just sent a pair of 430's in for warranty. Im talking the ones Before the blue handles. look like i dug them up from 50 years of dirt. the "tongue" was broken. Along with a pair of brand new 338 that had a chip in the cutting edge. Both were replaced within about 2 weeks. I'm a PA boy...

Dang that is a sweet guage. How bout posting the number of that. Looks like i may make an "impulse" buy. Thanks

3/4" drive sockets and ratchet.