Show your new tool arrivals

[rharman]

The wife pretty much just rolled her eyes. ..

Years ago, I bought one of those side cabs. Put it on wheels. It slides right around/over the base of my drill press and under the table. Great for keeping all the drilling doo-dads close by.

 

[NUTTSGT]

Hey, an end cabinet was how we did it in the old days! If you were a big deal and had a lot of tools, you hung that little assortment of more drawers off the end of your cab. Nowadays we just buy another cabinet or whacking huge cabinet!

Yeah.....I've that a couple of that already...still have 56" bottom on order...

 

[NUTTSGT]

Years ago, I bought one of those side cabs. Put it on wheels. It slides right around/over the base of my drill press and under the table. Great for keeping all the drilling doo-dads close by.

I bought this one for all the hydraulic press stuff with some room to grow.

 

[four.cycle]

oooo I'd never considered putting one of those on wheels. I'm intrigued. $279 out the door. Just called 6th ave store.
but... I wasn't planning on spending any more money this week....
====

in other news....

These were also waiting for me at the post office earlier today:

6 inch brass wheel from China. Looks like a real piece of garbage. Super cheap on Amazon. Hope I don't put my eye out, kid.
S-K Tools U.S.A. LLC graciously shipped me a 42470-2 repair kit for a 42470 1/2" drive ratchet that's frozen up.
They could not have made the process any easier. I was actually a bit surprised that it was so easy.
YMMV

 

[Squankum]

oooo I'd never considered putting one of those on wheels. I'm intrigued. $279 out the door. Just called 6th ave store.
but... I wasn't planning on spending any more money this week....
====

in other news....

These were also waiting for me at the post office earlier today:

6 inch brass wheel from China. Looks like a real piece of garbage. Super cheap on Amazon. Hope I don't put my eye out, kid.
S-K Tools U.S.A. LLC graciously shipped me a 40270-2 repair kit for a 40270 1/2" drive ratchet that's frozen up.
They could not have made the process any easier. I was actually a bit surprised that it was so easy.
YMMV

Did you ship them the ratchet, too, or did you just bag it up as a reminder while you waited for parts?

 

[four.cycle]

I emailed them a photo of the ratchet disassembled and told them it was frozen up. That's it.
No receipt.
It's a model 42470 - 1/2" drive RHFT - I got the part number wrong above (now corrected.)
Took about a week for it to arrive. Prepaid. No charge. Could not have been easier. No "back and forth". Just "Okay, on the way!"

(* now I'm wondering... did I get the super fine-tooth version?)

* I bagged it so I didn't lose that clip ring!

 

[Jgaz]

Hey, an end cabinet was how we did it in the old days! If you were a big deal and had a lot of tools, you hung that little assortment of more drawers off the end of your cab. Nowadays we just buy another cabinet or whacking huge cabinet!

I liked my end cabinet when my work box stack was mostly stationary.
When I changed departments and had to move my box at least 75 or more yards each shift it was a loser.

Sold the end cabinet, sold the mid riser section (wish I’d kept it for home), sold the top box, all SnapOn.

Bought a SnapOn KRA roller cabinet and set a machinist chest on the top when doing machine shop work.

 

[Squankum]

I liked my end cabinet when my work box stack was mostly stationary.
When I changed departments and had to move my box at least 75 or more yards each shift it was a loser.

Sold the end cabinet, sold the mid riser section (wish I’d kept it for home), sold the top box, all SnapOn.

Bought a SnapOn KRA roller cabinet and set a machinist chest on the top when doing machine shop work.

Electrically driven wheels have got to be coming someday!

 

[rharman]

@four.cycle - I was worried about the side cabinet toppling over if I just put wheels directly under it. You can see I made a base out of 3/4" plywood to get the wheels slightly outboard all around. It rarely moves but I haven't had any instability issues with it. I do keep close control of it though when moving.

 

[rharman]

Several things over the past couple of weeks....

Cover for the arbor hole of my Kreg Track Saw. Helps with dust collection.
Paint can shaker for the recip saw
Makita impact rated bit set - 60 piece
Setup block set
Pair of 1-2-3 blocks
LED gooseneck light. Going to try it as a shadow light on the miter saw.
A pair of ferrite ring magnets. Keep the metal swarf in check on the drill press.

 

[Semi-hole mechanic]

Motorhead friends would cut them open with various nasty blades--don't want to introduce any shavings--to monitor engine health, especially during break-in and hard track use. A proper can opener like that makes very good sense, and prevents blood contamination during the inspection.

Watched my friend do it to one of their midget motors when he built his and his brother’s “Iron Dukes” in the early ‘90s before they had the money to buy professional built engines ( they run Stanton Mopars now). He was refreshed a motor put it in his car and did a break in and put some hot laps on it. He cut the filter open to check for any large amounts of metal flakes before he pulled it and stuck it in their trailer as a backup motor.

 

[NUTTSGT]

oooo I'd never considered putting one of those on wheels. I'm intrigued. $279 out the door. Just called 6th ave store.
but... I wasn't planning on spending any more money this week....
====

$239 Inside Track Price

 

[ETJ]

New Snap-on 312SIMFYA 3/8" SAE deep impact socket set,
And similar shallow set (IMF) missing one (1") socket.

Snap-on metric 1/4" shallow magnetic power socket set (MGMM) missing 10mm and 12mm. All are unused. (For €30)

Barely used 1/4" metric impact socket set (SIMTMM).

Mac tools USA 30mm, 32mm and 36mm deep impact sockets



Old Snap-on TDM-117A Metric tap & die set. They have seen very little to no usage.


Brand new Mac tools SAE Tap & Die set TD41SAES-US.

 

[SC Fly Guy]

I sometimes paint with a chip brush like the one pictured. But as soon as I switch back to a better quality brush, it is immediately clear why this is a bad bad idea if you are doing more than a tiny spot. The brushes shed too many bristles and do not hold paint well. So painting takes much longer with them and does not come out as well.

Cheap me, I also wash and reuse chip brushes. They get worse and worse each use as they shed more bristles. I think more start to break off till they become fully bald.

Been absent with the influx of family for the 4th …

My father-in-law was a painting and wallpaper contractor after serving in WWII. He later opened a paint and wallpaper shop. He refused to sell any cheap stuff … exclusively Pratt & Lambert paint (before the name got bought) and the best brushes - pricy even 25+ years ago. He REFUSED to use foam even for quick projects and gave me an earful when he saw them in my paint cabinet! He’s been gone 30+ years, but I still think about him when I pull out a cheap brush!!

 

[four.cycle]

$239 Inside Track Price

oh! wow! thanks! I never even think about that.

He REFUSED to use foam even for quick projects

I used to be the same way. Had to use all top-end stuff, everything had to be prepped, primed, sanded.
I finally came to the realization that barring large holes or major imperfections in the surface, 99% of the people are not paying one damn bit of attention to what YOUR walls look like in your house.
There are a whole LOT of cases where "good enough" is truly "good enough" and going farther simply doesn't make any sense.

 

[four.cycle]

following up on my post from yesterday:

I put the S-K 42470 1/2" drive RHFT ratchet back together last night with the repair kit that S-K shipped to me.
I believe this must be the "super fine tooth" version, as this baby is so nice now I may well keep it!
They are supplying the ratchet repair kit with Lubriplate "Clear Plex-2" - a food grade lubricant. Not as thick as vaseline, but thicker than K-Y Jelly. This thing is slicker than deerguts on a doorknob now.