...so I bought this house.

[stokefire7]

I need least three characters.

 

[stokefire7]

My message is too short.

 

[stokefire7]

Bummer, I couldn't find my spring clamps. Bought new ones at the big box to hold down posters on a dry erase board. I guess there's oil on the plastic ends.
Who knew ?

 

[stokefire7]

Good morning.

 

[stokefire7]

Roadtrip !

 

[stokefire7]

Yahoo !

 

[Daniel441]

I was listening to Pink Floyd Animals at the time (in case you were wondering).

That’s a beautiful song


Sent from my iPhone using Tapatalk

 

[stokefire7]

Salvage !

 

[LS6 Tommy]

Salvage !

Those are great!

Tommy

 

[JR 42]

I love old mop sinks, nice work! Minor pain in the *** to plumb I'd guess.

 

[stokefire7]

Those are great!

Tommy

Ordered the trap standard today, delivery on the 9th.

 

[stokefire7]

how is the construction going today?

Good question. Slow. My 200 mile a day commute and full time job take more out of me than I think.

 

[stokefire7]

I love old mop sinks, nice work! Minor pain in the *** to plumb I'd guess.

They had two in this school their demo'ing . Had some other things too. Got all the pencil sharpeners I could lay my hands on. LOL Missed out on a kiln. Second pic is of some mini splits. I couldn't believe the air compressor was going to scrap. I'll post the rough-in for waste and water when I get the trap.

 

[LS6 Tommy]

Ordered the trap standard today, delivery on the 9th.

I hope you got the one with the trap cleanout.

Tommy

 

[LS6 Tommy]

They had two in this school their demo'ing . Had some other things too. Got all the pencil sharpeners I could lay my hands on. LOL Missed out on a kiln. Second pic is of some mini splits. I couldn't believe the air compressor was going to scrap. I'll post the rough-in for waste and water when I get the trap.

I can relate to this. In the 18 years I worked for school districts, I saw lots of relatively nice and easily cleaned up auto shop, wood shop and metal shop equipment go in a dumpster. If I had space, I could have had almost a full shop. Delta Rockwell drill presses, table saws, grinders, polishing centers, wood & metal lathes... They scrap it because they're too lazy to sell them and also afraid of any liability they might incur if they sold them. I've saved a few little things here and there.

Tommy

 

[stokefire7]

Too FAST !

 

[stokefire7]

Pilot operated PRV.

 

[stokefire7]

I need 10 1/2" above finish floor for the drain. A 5 5/8" center to center set gives me an 8" center to center travel.

 

[stokefire7]

I need to drill out around the pipe for the fitting hub.

 

[stokefire7]

Check depth. Ream and chamfer. Weld.

 

[stokefire7]

I need to make a plug. Perfect for some old fence post.

 

[stokefire7]

Was going to use these for an arch over two posts but. Maybe part of my weld cart, had a couple uses laid out. I need a 2" ****** now. Did get to try out my new saw, works very good, really pleased with it.
I had a suspicion that this maybe some Oil Country Line Goods but the way it cut I'll bet it's good ole sch 40 black. We'll see how it threads.

 

[stokefire7]

I could go buy a ****** but that's not the point is it . I'm up for some low resolution machining.

 

[stokefire7]

..to seal it

 

[stokefire7]

Can't find any info on the sink , no rough in dimensions. I'll have to wing it.
First issue I see. Had a glob of porcelain, potential leak.

 

[stokefire7]

At a 10 1/2" rough-in. Top of trap standard would be 15".

 

[stokefire7]

Layout on the sink.

 

[stokefire7]

A couple other dimensions I needed.

 

[stokefire7]

Minus backing for hanger.

 

[stokefire7]

It's Royces fault.

 

[nadogail]

Thanks for sharing.

 

[stokefire7]

Thanks for sharing.

Had fun. I'm gonna try the blunt end next.

 

[stokefire7]

Weld cart it is !

 

[stokefire7]

Road trip!

 

[stokefire7]

Finished up some trim on the fence( pay no attention to the form wood there on the ground, the other concrete guy I ran off hasn't came back for it).

 

[stokefire7]

…some progress