The Milwaukee addiction thread! :)

[ptgarcia]

Since I have mostly Milwaukee stuff and LOVE it, but have a few Ryobi 1+ tools for those little once in a blue moon jobs that I just can't justify shelling out the big $$ on, have this little project in the works....

I've tested with an old m18 battery and a few different Ryobi tools, and so far no issues, so off to the 3d printer I went. Still need to wire the prototype up, but the fit is solid---and for $10 Canuck-Bucks total investment I'm happy so far haha.

Plan is to make 3 final versions and leave them in my Ryobi blower for clean up, the nail gun for the odd time i do trim, and the weed wacker. I have all under $150 Canadian for three of those but I hate having more than one battery system.

This is a great idea. I'd love one of these for my Craftsman C3 tools.

 

[kctyphoon]

This is a great idea. I'd love one of these for my Craftsman C3 tools.

I suspect you can sell a few on here (right on this thread even) if you wanted to.. the nailers alone have a pretty good reputation..

 

[ptgarcia]

I suspect you can sell a few on here (right on this thread even) if you wanted to.. the nailers alone have a pretty good reputation..

That's just it, I like them and don't want to sell them. But it sure would be nice to be able to use my M18 batteries with them!

 

[chrisexv6]

I actually have a set of Ryobi batteries that I bought with the intention of using JUST for the cordless nailers. Ive since acquired other "one off use" Ryobi tools (right angle drill, etc) so I keep the set around for the stuff I dont want to buy in Milwaukee since Ill only use them occasionally.

I only have the 16 ga Ryobi nailer so far but its a really nice piece and the price sure beats buying Milwaukees.

 

[CoreyHendo]

I suspect you can sell a few on here (right on this thread even) if you wanted to.. the nailers alone have a pretty good reputation..

I was thinking the same thing. Would love to have them just for the nailers.

 

[bcradio]

I own two 5.0 batteries and two of the compacts between the fuel impact driver that has the self tapping screw mode, a fuel drill driver and a fuel sawzall. Would buying the 9.0 benefit me on the sawzall or is the weight trade off not worth it? I keep the two 5.0 with the sawzall currently.

The 5.0 works just fine on the sawzall. No need to get the 9.0 for that.

The circular saw would benefit from the 9.0 though. However, the 5.0 works fine on it as well

I much prefer to use the 5.0 with the sawzall.

 

[CoreyHendo]

The 5.0 works just fine on the sawzall. No need to get the 9.0 for that.

The circular saw would benefit from the 9.0 though. However, the 5.0 works fine on it as well

I much prefer to use the 5.0 with the sawzall.

Wait, we are talking need here? Haha. Most of us can make due with corded tools. We just don't want to.

 

[bcradio]

Wait, we are talking need here? Haha. Most of us can make due with corded tools. We just don't want to.

Well he'll certainly need the 9.0 battery for his miter saw, blower, string trimmer and vacuum that he'll need to purchase to remain in the club.

 

[bert1913]

https://www.amazon.com/gp/product/B015HOY8SI/?tag=atomicindus08-20

 

[starquestMM]

I'd take an adapt or also. Looks like someone is selling them on Ebay for $54 from Australia.

 

[DerekV]

I own two 5.0 batteries and two of the compacts between the fuel impact driver that has the self tapping screw mode, a fuel drill driver and a fuel sawzall. Would buying the 9.0 benefit me on the sawzall or is the weight trade off not worth it? I keep the two 5.0 with the sawzall currently.

The real life perceived weight of the Sawzall with a 9.0 vs. 5.0 is negligible. Definitely not nearly big enough for me to want to use a 5.0 over the 9.0. It's balanced well.

The 9.0 on the Sawzall is awesome. I wouldn't trade it for something lighter or corded (although I do want the Hackzall). If you're really giving it a hot supper, it makes a huge difference in power and run time. Not just run time, but power. It doesn't slow down at all under heavy load. These conditions will also put more wear on a 5.0 over a 9.0 since there are less cells to draw current from - so it'll be "maxed out" while the 9.0 will be at "2/3 throttle". So if you're aiming for any sort of longevity out of these batteries, that's something to consider.

But I guess if you're just cutting twigs and plywood, a 5.0 would be more than fine. Just be prepared to have extra batteries on-hand for long/demanding tasks - it gets thirsty. BUT with the $250 9.0 kits out there now, it's hard to say no...even at full price they're a steal...

My $0.02

 

[number626]

10 ton knock out up to 4"

 

[number626]

Some lights.

 

[kctyphoon]

Some more pics of the mid torque impact.. I've seen it being compared to the 1/2" high torque, but not compared to the 3/8 model.. so one pic is with the battery packs lined up, to give you and idea how much of the high torque actually hangs off the back of the impact. The other is with all the backs lined up to show overall size.. not sure everyone realizes how small this new impact actually is.. note, this is the gen1 3/8..

 

[DFB]

Ya the overall length is pretty good something like only one inch longer than a compact.

Still it's got some girth

Obviously a much bigger motor/impact mechanism but that's where its going to count!

 

[Hendricks433]

Man I'm in the market for 1 or 2 of those. That makes the decision really hard.

Size of the mid torque makes me think I could get by with my M12 Fuel Impact and the Mid Torque 1/2 for all my auto/motorcycle work.

 

[bcradio]

The mid torque impact is awesome. I agree that it is a game changer. With a 5.0 battery it feels about the same weight as my 2235. Granted I haven't weighed them.

 

[kctyphoon]

Also - the Neiko underhood light I bought came today.. it's BRIGHT.. Do NOT even consider the HF model for you home mechanics. I have both now, and there is NO comparison between them.. the Neiko underhood light is exactly a larger version of the Neiko and Capri tools small led light, with the option of a high/low setting and the underhood mount - which is a dual spring loaded clamp btw.. its not a $250 model. The hood clamp is a little on the cheaper side, but the light itself seems pretty great. The plastic tube/lens of the light actually has some flex in it which I feel is a good thing instead of being super stiff and prone to breaking if it's dropped. I can probably drop the light itself off my roof without it sustaining damage.

For about twice what I paid for the HF model (I posted a link for the Neiko on eBay for $69 shipped, I paid $79 though Amazon) you get a light that puts that HF to shame AND an actual spring loaded hood clamp.. I haven't used the light yet, probably won't for a while, but it's way better than HF by all standards, and you get ALOT more for your money.. it will also work both cordless and corded..

So far the only thing I wish were different, is I wish the hood clamps didn't twist in the tubes, meaning - I'd like if they slid on a bit of a track that kept both sides facing upright, and unable to turn.. the fact you can have one hook pointed up, and another pointed down or to the side MIGHT be a plus for some people, but I personally can't think of a situation most people would want that.. a plus on the other side is the light is completely detachable from the hood mount, giving you a 4' (guessing) light wand that might do wonders for you under a car. The design of the Neiko keep the light from rolling around..

If you've been wanting an underhood light, don't wanna spend a lot, don't wanna wait for a possible Milwaukee, I suggest you give it a look...

 

[Project_shadow]

My new addition, I can now take my poor non fuel home and give it an easy life trimming .223 cases



Sent from my iPhone using Tapatalk

 

[Tallpilot]

Some more pics of the mid torque impact.. I've seen it being compared to the 1/2" high torque, but not compared to the 3/8 model.. so one pic is with the battery packs lined up, to give you and idea how much of the high torque actually hangs off the back of the impact. The other is with all the backs lined up to show overall size.. not sure everyone realizes how small this new impact actually is.. note, this is the gen1 3/8..

Thanks for those. I only have the high torque and the mid torque. It is amazing how small it is for the power it has. I hope it will fit everywhere I need it too and won't have to buy a smaller one.

 

[Badger 13]

KC,
Now that you have the mid torque, what are thoughts on it, or opinions ?

Thanks

 

[DFB]

Also - the Neiko underhood light I bought came today.. it's BRIGHT.. Do NOT even consider the HF model for you home mechanics. I have both now, and there is NO comparison between them.. the Neiko underhood light is exactly a larger version of the Neiko and Capri tools small led light, with the option of a high/low setting and the underhood mount - which is a dual spring loaded clamp btw.. its not a $250 model. The hood clamp is a little on the cheaper side, but the light itself seems pretty great. The plastic tube/lens of the light actually has some flex in it which I feel is a good thing instead of being super stiff and prone to breaking if it's dropped. I can probably drop the light itself off my roof without it sustaining damage.

For about twice what I paid for the HF model (I posted a link for the Neiko on eBay for $69 shipped, I paid $79 though Amazon) you get a light that puts that HF to shame AND an actual spring loaded hood clamp.. I haven't used the light yet, probably won't for a while, but it's way better than HF by all standards, and you get ALOT more for your money.. it will also work both cordless and corded..

So far the only thing I wish were different, is I wish the hood clamps didn't twist in the tubes, meaning - I'd like if they slid on a bit of a track that kept both sides facing upright, and unable to turn.. the fact you can have one hook pointed up, and another pointed down or to the side MIGHT be a plus for some people, but I personally can't think of a situation most people would want that.. a plus on the other side is the light is completely detachable from the hood mount, giving you a 4' (guessing) light wand that might do wonders for you under a car. The design of the Neiko keep the light from rolling around..

If you've been wanting an underhood light, don't wanna spend a lot, don't wanna wait for a possible Milwaukee, I suggest you give it a look...

Cool

Seems to have good amount of lumens over the two settings and priced fair enough.

Does the HF even give lumen rating don't even see one listed

Just advertising the amount of bulbs alone don't mean much especially if they just are like little Christmas tree lights

I had a cheaper 12v fluorescent unit long ago I liked it a lot but everything broke on it...the hook the stand all cheap sh*t.


I still wonder if the there is an optimum point to just how bright an under hood light should be I have used various lights. Stick lights at around 300 lumens sometimes aren't bright enough though the full 1000 lumen setting on my M12 Rover was a bit much over my tractor engine. Was slightly better toned down. Haven't tried it yet under my Durango hood a much bigger engine bay.

Around 700 often seems good to me. I couldn't imagine that ATD Saber with 2000 lumens except for under chassis where you can usually use more light if your not just being site specific.

I had thought the Milwaukee Rover LEDS were going to be great for some of my motorcycle wrenching but I found out they almost impossible to use around them with all the reflective surfaces, believe or not I still use shielded droplight and screw base bulb for that stuff.

 

[DerekV]

My new addition, I can now take my poor non fuel home and give it an easy life trimming .223 cases



Sent from my iPhone using Tapatalk

I LOVE my 2703. Excellent drill.

 

[dacan23]

Still surprised it took HD so long to get this stuff in. Hedger says 2hrs of run time, unfortunately the one I dont need has the longest run time; Hedge 2hrs, Wacker 1hr, Blower 25mins.

Also they are finally getting a new 2897 kit I have seen in their system for a while. It comes with a 5.0 & 2.0 for 299, too bad it wasnt a 6.0. At 299 its a better deal than 2x5.0s at 349.

 

[signcrafter]

Was just in HD and looks like most of the tools prices have dropped. I bought an m12 fuel kit two weeks ago for 230 and got a free ratchet. Today that kit is 169 but no free tool. I asked if I was eligible for the price difference and they said sure and refunded me 63 dollars.

Decided to go take advantage of the free m18 fuel circular saw deal when you buy the 9 amp battery. Really thought about picking up the m12 circular saw also for 120 bucks to use as a trim saw. But had to stop somewhere. This m18 and m12 addiction is getting really expensive!

 

[Hendricks433]

Was just in HD and looks like most of the tools prices have dropped. I bought an m12 fuel kit two weeks ago for 230 and got a free ratchet. Today that kit is 169 but no free tool. I asked if I was eligible for the price difference and they said sure and refunded me 63 dollars.

Are you serious? I just bought the fuel kit with the free ratchet 2 weeks ago. I may have to swing in and see what they say. Worst they'll say is no right?

 

[bcradio]

Was just in HD and looks like most of the tools prices have dropped. I bought an m12 fuel kit two weeks ago for 230 and got a free ratchet. Today that kit is 169 but no free tool. I asked if I was eligible for the price difference and they said sure and refunded me 63 dollars.

Decided to go take advantage of the free m18 fuel circular saw deal when you buy the 9 amp battery. Really thought about picking up the m12 circular saw also for 120 bucks to use as a trim saw. But had to stop somewhere. This m18 and m12 addiction is getting really expensive!

You lucky duck... getting the M12 kit with the free tool for $169.

I'm still debating on the m12 fuel circ saw as well as the m12 bandsaw.

 

[signcrafter]

Are you serious? I just bought the fuel kit with the free ratchet 2 weeks ago. I may have to swing in and see what they say. Worst they'll say is no right?

See what they say. I just brought my receipt and asked nicely if I was eligible for a price refund. They looked it over and said yes.

The m18 fuel circular saw is nice. I got it mainly for the 9 amp battery and the rapid charger. If it wasn't for that deal I probably would have done the m12 fuel saw for the 129 or whatever it was. The m12 is a nice light weight saw and I'm sure being a fuel it has plenty of power. Will probably pick it up in the near future to use as a trim saw.

 

[signcrafter]

You lucky duck... getting the M12 kit with the free tool for $169.

I'm still debating on the m12 fuel circ saw as well as the m12 bandsaw.

Don't forget the 11% rebate match they are doing this week if you have a Menards near by!

 

[bcradio]

Don't forget the 11% rebate match they are doing this week if you have a Menards near by!

No Menards around here either

 

[whitetailhntr]

Don't forget the 11% rebate match they are doing this week if you have a Menards near by!

Homedepot?


Sent from my iPhone using Tapatalk

 

[chrisexv6]

Was just in HD and looks like most of the tools prices have dropped. I bought an m12 fuel kit two weeks ago for 230 and got a free ratchet. Today that kit is 169 but no free tool. I asked if I was eligible for the price difference and they said sure and refunded me 63 dollars.

Decided to go take advantage of the free m18 fuel circular saw deal when you buy the 9 amp battery. Really thought about picking up the m12 circular saw also for 120 bucks to use as a trim saw. But had to stop somewhere. This m18 and m12 addiction is getting really expensive!

Lucky you got the free ratchet! The 169 price is part of Pro-week, though, so its expected.

As far as M12 stuff goes....talk to my M12 Fuel hammer drill, Fuel Hackzall, Fuel circ saw, stick light, non-Fuel drill, and soon to have Rover light

I too bought the M12 Fuel circ saw, but only so I could complete the collection (!!!) I had both M18 Fuel circ saws and the M12 Fuel circ saw is clearing out of some stores at $75.00, so I figured WTH.

 

[DerekV]

Also they are finally getting a new 2897 kit I have seen in their system for a while. It comes with a 5.0 & 2.0 for 299, too bad it wasnt a 6.0. At 299 its a better deal than 2x5.0s at 349.

Agreed. That's a good kit. I actually prefer the compact batteries on impact drivers.

Speaking of which, I still want a Fuel impact. Getting tired of using the 1/2"-1/4" female adapter on my 2755B and while I love my RA impact, it'd be nice to have a conventional pistol grip style one. I just dunno what to get.

It'll be used mostly on vehicles/motorcycles for small fasteners and quick changes between drive styles, so I think the Surge is outta the question since it's only really meant for driving screws. Then there's the tried and true 2753, which is tempting since it's simple and cheap. I'm really interested in the OK version though so I can manipulate the drive modes. I'd love to have a mode that ramps up slowly, spins fast, then stops right before it wants to impact (almost like a "finger tight" setting). Another mode that's just a little more powerful than that, maybe a couple impacts. Then one that's balls to the wall maxed out. And finally one for self tappers.

I don't know, what do you guys think?

 

[bcradio]

I too bought the M12 Fuel circ saw, but only so I could complete the collection (!!!) I had both M18 Fuel circ saws and the M12 Fuel circ saw is clearing out of some stores at $75.00, so I figured WTH.

Are you able to locate which stores have this price online, or do you need to go in store for this?

 

[chrisexv6]

Are you able to locate which stores have this price online, or do you need to go in store for this?

In store only, the only price I ever saw on the web was full (regardless of which store I picked)

 

[bcradio]

In store only, the only price I ever saw on the web was full (regardless of which store I picked)

Thank you sir. I may have to drive around this weekend.

 

[Tallpilot]

Still surprised it took HD so long to get this stuff in. Hedger says 2hrs of run time, unfortunately the one I dont need has the longest run time; Hedge 2hrs, Wacker 1hr, Blower 25mins.

Also they are finally getting a new 2897 kit I have seen in their system for a while. It comes with a 5.0 & 2.0 for 299, too bad it wasnt a 6.0. At 299 its a better deal than 2x5.0s at 349.

/sigh It is a full time job trying to keep up with these kits and how much discount they provide, etc. I do wish they would make more kits with 1 battery like I used to buy my high torque impact. I would rather have one newer 2.0,3.0,5.0,6.0,etc than 2 batteries from 3 generations ago.

 

[signcrafter]

Homedepot?


Sent from my iPhone using Tapatalk

Yes IF you have a Menards close home Depot will match their rebate the weeks Menards has them. But you have to ask for the form. Or you can print it out online. But they told me they aren't supposed to offer it out or advertise that they match. Only of the customer asks.

 

[LB-1911]

Homedepot?

As previosuly mentioned, are you in the vicinity of a Menards?

GET YOUR 11% REBATE MATCH
(Select Stores Only) March 12, 2017 – March 25, 2017
https://www.homedepotrebates.com/11percentmatch/

 

[kctyphoon]

Cool

Seems to have good amount of lumens over the two settings and priced fair enough.

Does the HF even give lumen rating don't even see one listed

Just advertising the amount of bulbs alone don't mean much especially if they just are like little Christmas tree lights

I had a cheaper 12v fluorescent unit long ago I liked it a lot but everything broke on it...the hook the stand all cheap sh*t.


I still wonder if the there is an optimum point to just how bright an under hood light should be I have used various lights. Stick lights at around 300 lumens sometimes aren't bright enough though the full 1000 lumen setting on my M12 Rover was a bit much over my tractor engine. Was slightly better toned down. Haven't tried it yet under my Durango hood a much bigger engine bay.

Around 700 often seems good to me. I couldn't imagine that ATD Saber with 2000 lumens except for under chassis where you can usually use more light if your not just being site specific.

I had thought the Milwaukee Rover LEDS were going to be great for some of my motorcycle wrenching but I found out they almost impossible to use around them with all the reflective surfaces, believe or not I still use shielded droplight and screw base bulb for that stuff.

To put things into prospective, I think the lumen rating on the LOW setting is about twice as bright as that of the smaller version, (or close to it) which is what I've been using to do the maintenance on my car now as an underhood light when it's dark, and even THAT little thing is way brighter then the HF model.. I honestly don't even bother using the HF cause the small Capri tools is just smaller and better.. I should have just returned the HF after I bought it, but it wasn't expensive and I figured wtf I'll just keep it..

I really REALLY like the small version.. probably my favorite work light for the car, Milwaukee stuff included.. the Neiko/Capri tools lights use much better LED's than the HF.. it's simply a better buy...