Search results

I just replaced the carb, filter and lines on this trimmer. Engine runs well [the carb is a ZAMA p22a (753-04338)] I cannot find markings or literature that describes which of these carburetor screws is the “H” and “L” or if they are idle speed and mixture instead. None of this stuff comes with...

Does This black wire goes in the only logical place on the metal contact? I should have taken a picture.

I thought this would be easy, but many manufacturers aren’t what they use to be. I need something cut fire wood that I would further use with a splitter. 16” or 18”? TIA

Howdy! I have my garage plumbed for air and for a while I noticed a very gradual loss of air pressure. The loss of pressure was making me crazy. I started at the hose reel, and every connection back to the compressor using the red leak detector and applicator. I was surprised to see a leak here...

Our Aprilaire humidifier died a few years ago. It hasn’t been that cold in the winters anymore to warrant replacing it. What happened to it you ask? The plastic housing that holds/supports the fan motor failed and the device suddenly made a terrible sound. I unplugged it and there its been. So...

After 40 years my inlaws home in New Hampshire is having drain issues. We had the line snaked from the septic tank and we had it snaked from the inside going out… the only other issue has to be venting. There are no visible vent stacks on the outside of the home so i feared my father in law did...

I suspect something may not be right…

Does anyone have an improvement hack over the OEM dust collection port? From Dewalt, it is better than nothing but someone by now has addressed this!

Battery charger comes on, display is green…..then after a few moments turns red. Are there generic chargers out there for Kobalt?

I just replaced the hinges and posted a link in another post. During the install it said not to remove the top and bottom hinges. I want to remove the top and bottom hinges one at a time to clean and inspect. Any issues or dangers involved here, I know this is a silly question but I am not...

I found a few post here that addressed this same issue. I tightened the screw this time, all the way up as tight as I could. This was after I noticed that when the door was opened and closed,and it moved ever so slightly laterally, the screw would back out Fractions of a millimeter. Over time...

i hope I can explain what is happening. This outside outlet is controlled by a switch inside the house. Right now it supplies power to the white icicle christmas lights which are still up. Sometimes when it rains, (i guess), the gfci trips and the little fault light stays dimly lit. I cannot...

are walnut shells a good media for removing surface rust from mild steel or iron hand rail?

This looks like a p-trap. Still smell sewer gas.

This is so aggravating. The handle comes off or should I say the &^%^&%#$%^#$&^#%^&$%*&^ handle is not attached. I suppose I could hit it with the MIG, but how do they usually attach these?

There is cold air coming from outside through the garage door. 18 years ago, the installers did not fine tune the installation so that the side seals sit flush and relatively air tight. I never noticed the difference from side to side. The left side of the garage door the seal sweeps the side...

this is for a replacement blade for the DMW 120 DeWalt portable bandsaw. The saw came with an 18 TPI blade which I broke last night and I replacing it with a Lennox 14/18. Tpi blade. Does anyone know what the 14/18 TPI blade is good for or used for. Thank you in advance.

Hi, I am trying to make an annealing machine. I saw a video where the guy used a microwave's platter motor to turn a plate. I successfully removed the motor from the microwave but I am at a loss on how to power this Synchronous motor. My first observation is the wires from the motor are of...

panasonic bathroom fan FV-LP002 with light. i replaced the bulbs. One is a panasonic bulb the other is a sylvania. The sylvania has a momentary delay and sorta clangs before it comes on. Anyone have any ideas?

I installed a panasonic bathroom fan FV-LP002 about 14 years ago. I was getting ready to do some cleaning maintenance to it, when i noticed the fan spinning around Slowly, but not fast. I pulled a permit for this bathroom project… at first i thought it was a convection from a/c vent…or power...