Search results

We know we need a second panel to upgrade a big shop expansion. Going too 320a with 2 200a panels. In doing so, we need to replace the meter with a double lug variety to supply both panels... (Unless there is a better way...maybe that is the question.). Question, based on the pictures...

I can't for the life of me figure out how to install the safety mechanism for a dannmar d10 cx. Any pictures? Spring isn't working... Sent from my Pixel 2 XL using The Garage Journal mobile app

At this point I dont have a table saw and was wondering what the thoughts are on a track saw vs a table saw. In the end, space isn't limited, it would be used maybe once a month, and I can't spend more then 800. Examples: https://www.amazon.com/dp/B000LZ31PU/?tag=atomicindus08-20...

Bring this thread back up as I am trying to do this with my 790 john Deere. Any other thoughts? Sent from my Pixel 2 XL using The Garage Journal mobile app

The problem with this one is that it is a 24" rack with the top cut out. I am doing almost the reverse except I don't care if the uprights stick out there full 44". I just don't want the table at 44". Sent from my Pixel 2 XL using The Garage Journal mobile app

Hello everyone, So I got 140' or pallet racking at auction and though I am grateful most is 44" deep, I would like to have 16' or so of work bench that is 24". Question. How would you reduce the lower depth to be 24". I possible could cut the tabs off the rails and weld them into place after...

If you can open the lines on both ends, you could do the bore dry method but use a electrical wire fish line and old rags. Count how many rags you put on....then when you pull it out. Sent from my Pixel 2 XL using Tapatalk

Time vs money then. What is harder to come buy? Do you want his height? Sent from my Pixel 2 XL using The Garage Journal mobile app

First question should be .... Will I have to pull a permit? If so will the jursidiction approve of it as built or do you need an engineer to approve the used materials? Using recycled material isn't covered under the ibc code. So. I just finished my pole barn. Prior guy tore it down...

How much sand are you getting and what size? I had a new well put in with mesh at the bottom and am getting a lot of material up still. I started off with two spin down ruscos....but after about 2500 gallons they would clog (think.....125psi....). so i would drain rinse...and repeat...

will this be spanning multiple beams or running parallel to one?

No markings and it looks like it has been in a garage for 30 years. I will strip the ends and continue on. Thanks gents Sent from my Pixel 2 XL using The Garage Journal mobile app

Sorry, didn't hit the attach button. Sent from my Pixel 2 XL using The Garage Journal mobile app

I got a 110' 10g stranded extension cord a garage sale for 30. I knew it needed new ends but in taking the old ones off I noticed it was wrapped in twill rope. Thoughts on what it is and if it is still safe? The cord itself has no abrasions. Sent from my Pixel 2 XL using The Garage...

I had really good success emailing the media relations contacts at our local cable company. They go up to executive leadership faster and get the right people involved really fast....ask me how I know......stupid Comcast..... Sent from my Pixel 2 XL using The Garage Journal mobile app

Who is pulling the wire? I would go one size up if you are pulling that length. Sent from my Pixel 2 XL using The Garage Journal mobile app

How about a pellet stove?? Sent from my Pixel 2 XL using Tapatalk

Not an electrician...but why not run a sub panel then a circuit or two back to the porch if you are so inclined? Sent from my Pixel 2 XL using Tapatalk

By flashing, you are talking about putting on a corded drill and running the Chuck by hand as hard as you can???? Sent from my Pixel 2 XL using The Garage Journal mobile app

Where does your footing drain....drain too? I would ensure there is an exit. I would add gutters and move water away Sent from my Pixel 2 XL using The Garage Journal mobile app