Search results

Hmm, not sure. 2 days ago? Makes more sense than it getting deleted for me asking a question about equipment I guess! hah

Maybe I'm losing it, but does anyone know why my thread about solving a strange Scissor Lift issue would be deleted? (I know it sat for at least a day without a response. Is that a reason?) I'll repost it but was hoping there were some ideas in it. Thanks guys

Thanks for the reply! I guess to be more specific, I am asking about their 'intended use' or certification rather. Not a guess on how leaky a garage is. I will phone the company and see what they say. Stay tuned (Although I suspect they will say not for enclosed spaces for liability...

Thanks. I'm aware of the sealed issue, although I'd say it's sealed as well as the rest of the house (attached garage, not some slanty pole barn). What I can't figure out is if these are meant to be run with the garage door shut or not, since it mentions how much combustion air needed right in...

Which one are you using? Where in Canada? I don't suppose you had it inspected (Not that I care directly about that, I'm wondering if there is some regulation about separated combustion). So all these people on this board that are using a Maxx heater.. Are they cracking a door?! When they say...

Hi guys! Sorry, I see a few threads regarding the Mr. Heater Maxx heaters (50K or thereabouts for my 2-2.5 car garage), but nothing that covers my concern. I understand about explosion risks with a 'non separated' heater, and that doesn't really concern my (I just usually turn wrenches. If I...

Yes. I have not read a single review where they claim the coverage is as expected. I wanted to go with the Rocksolid, but some were claiming it took them 6-8 kits for a 2 car garage....

So if it could be done would you recommend? Or just pour it on and squeegee it on as is? Thanks!

Hi there, thanks for the reply. Yes I will be acid etching. My question was more regarding if 100% solids is ever reduced to be used as a primer before applying at full viscosity. I have already extensively looked into the vendors here. It is too expensive now that our dollar has taken a...

Hi guys. Covered my garage in Resurfacer (It was pockmarked) and purchased a bunch of kits of 100% Epoxy (Nothing special. From a local retailer in Canada. I ordered them in). There is nothing about using a primer. I know on cars, we can use reducer on epoxy and spray it as a primer/sealer...

I think there is some great confusion about what OCD is in this forum.

Sounds like quite the pricey game plan! Advantage of using epoxy and sand over another self leveling polymer compound?

Well I'm not paying someone to do it, but if a skim coat can chip off, that sounds pretty bad too. I COULD just patch each individual piece of aggregate that is missing. The problem is, by the time I do that, I may as well just should have had some runny concrete mix of some sort and squeegeed...

No worries! Almost debating trying Quikrete Resurfacer, although I've never heard anything good! hah! Of course, what' sthe worst thing that happens, I have uneven, pitted concrete afterwards? hah! Also, unrelated to those trouble areas (Because I COULD just use patching compound there), I'd...

Yeah, I may not even waste my time looking for such a trivial thing. Any other suggestions? I can't tell if my application is indoor or outdoor. I also can't tell if it's a wear surface (I will coat it with something, but). I really just wan to smear a thin, thin layer of something all over...

Mayhaps, who knows. This is a lot longer than 30 years, as well.

Hey guys. Yes it may have been from salt dripping off car and freezing, but I purchased the house 2 years ago. I hope I've solved that problem (Well, not completely. But put new seals on the garage door. I am insulating it better, and who knows what the previous owner did. There IS a slope in...

Looking to pour some self leveling over my whole garage floor. She's quite pitted. I was going to use Quikrete or some such but haven't read anything good. Then I looked at Mapei, and while it has good reviews, it says it's not a 'wear surface'. Would this actually matter in the case of a...

Thanks guys! I thought a vapor barrier would be more common with everyone. Maybe it's only code in Ontario?? I, for some reason, can't seem to find faced insulation up here (?!). I'm debating trying to leave the kraft in the wall, if it will separate, but, does anyone have experience with...

Dang, that was my fear. hah Spray foam would work well? What about a thin (1"?) then apply batts again? And it IS on the house side I need the VB right?