Search results

Any pictures? I'm also looking at the primed t1-11, trying to decide if I want to go with that or sanded ply..?

But what I'm asking is.. do I need to stud regular walls or can I do bookshelf (horizontal) girts? The t1-11 will be installed vertical so my joints would be nailed every 2ft. Does that make sense ?

Has anyone used t1-11 for the interior walls in pole barn? 24x36x12 I'm trying to decide if it would be better to install regular vertical studs or bookshelf girts 24" o/c. My questioning comes into play when I think about the joints and a flat service for the tongue/groove to go together. Will...

I just had my 24x36 floor done. 4500psi 4.5" thick. Ordered 12.5yds. Hand trowel and saw cut. I did all the prep work including stone, expansion joint foam, vapor barrier, wire mesh and I sealed it after. they came and poured/finished. After fuel fees, concrete was about $2800 for 12.5 yds...

I looked at that Prodex, 10m would be R22. I'm not sure if it would sag with 4' center trusses

I'll take a look. Thanks

Good to know about the rolled insulation trapping dirt. That was my other option if I don't leave the trusses exposed. Spray foam is way too expensive around here. I talked to a guy that spray foams in my area and he said figure around $10k for the roof only, that was for 2in. Building is...

Buffalo Ny. We see all seasons, Temps can get down to the negatives during winter with feet of snow lol. Summers can be hot and humid. I'd like to insulate the building and keep it around 45-50 during the winter months.

I'm getting ready to insulate my pole barn. I'm looking for help insulating my ceiling. I would like to keep the trusses exposed, rather than put a ceiling in and insulate that way. Here's some pictures, they used double bubble on the roof. I was wondering if I could use the 4' x 50' blanket...

I was looking at those in Black, I've narrow it down to those in black or the square ones to go on both sides of the garage door and one on the side of the man door. Then one of these in the picture for above garage door

That's why I'm asking what other people used. To get ideas. I don't want just regular cheap looking lights. I'd like it to look residential rather than commercial since it's right in my front yard.

Anyone else have any exterior lighting? Other than the gooseneck lights? Would like it to look nice as well as enough light

Here's my 24x36x12 pole barn I just had done. I'm getting crete poured today. I've already added a sub panel, outlets and lnterior led lighting. Now I need some ideas for exterior lighting. I'm looking for ideas that will go with my building. I'd like to add a motion light next to or over man...

I've checked all return vents. Filter is new. No major dust around blower either

I have central air and boiler for heating. My central air wasn't blowing as hard and not cooling the house. I removed the cover on the air handler and the blower was running but the coil was iced over. I let it thaw for a day but it still isn't blowing hard. Put a new capacitor in and no change...

My question is for the guys who have pole barns in upstate NY. When pouring concrete floor, did you or the contractor use expansion joint at all? Did they pour right up to the posts or bottom board or did they use expansion joint up against the wood? I'm in Buffalo Ny and we have some harsh...

Conduit is already buried, I'll have a 8x8x4 weatherproof junction box on the outside of garage and a LB right inside the pole barn directly under the panel. I came up into the pole barn instead of outside. Panel will be when you walk in, behind the door.

I'm jumping off my detached garage panel, so there's no way to run additional wires etc out to the barn unless I cut out my driveway and run it underneath. So just power for me. I have a wifi mesh system, you just place s router in the garage, plug it in and now that's your wifi hub. Been...

Here's some pictures

Pole barn just went up. 24x36x12. Mixed use, work area for small engines, snowmobiles, atvs that kind of work. Storage and Also eventually a hang out area. I have a couple questions on whether I should run the conduit into the building or right up to the outside wall and through the wall...