Search results

You're not kidding. You need to make a spreadsheet with all their models just to keep it straight.

That is the 2763-21XC which is 700/1,000 lb ft and only two drive modes vs the 2767-21XC is 1,000/1,400 lb ft and 4 drive modes. Still not a bad deal though.

Darn, it seams to be gone.

http://www.amazon.com/gp/product/B002AS9IGC/ref=gb1h_img_c-3_8022_1dd0c282?smid=ATVPDKIKX0DER&pf_rd_m=ATVPDKIKX0DER&pf_rd_t=101&pf_rd_s=center-3&pf_rd_r=0Q5S4ZWFXZFVDH3404HM&pf_rd_i=384082011&pf_rd_p=1673798022 Not sure it is that great of a deal @ $48.10, but I thought I would mention it

Darn, I just bought the craftsman 19.3 volt drill/2 batt combo for the same price

I wonder if those are online only?

I was thinking three circuits, basic light coverage for daily use mostly focusing on around the vehicles and the walk path to the door, then extra lights over the vehicle section, then extra lights over the work section Per code for dedicated outlets like lights I don’t have to have gfci on...

Using 4' does make more sense in that respect Haha, those are jsut where i was putting the trash and recycle cans, they are very mobile:lol: Yea I was going to make a path down the middle of lights Thanks for that layout, I may end up using it more or less My dad has T5's in his shop and...

I did a quick redraw with more lights. It seams a bit excessive to me but I thought I'd see what the reactions were. I also put rough locations of the vehicles/ bikes. All the other objects shown are some sort of machine or cabinets. BTW I appreciate everyone's input, I don't mind being...

I wouldn't mind some input on my two lighting plans for my almost 30x40 garage with 10' ceilings. Fixtures will be surface mounted 4' double T8's and 8' quad T8's. The garage is drywalled and painted a extremely light semi gloss gray. Since I can get into the attic I figured it would be...

I had a 24x24ft drywalled garage attached to the house that I added 16' to. I was able to get kraft faced r-19 for the walls @ $16 a roll from HD so was all set there For the ceiling the existing garage has r-30 kraft faced insulation just laying inbetween the trusses. I don't think the...

I just got done measuring the ceiling and there will be some sections that are 16'2". Does this mean I need to get 10' sheets and cut them to 4'2" or can I make up that much gap with mud and the space for the wall drywall?

I’ve only hung drywall a couple times so had a question about my garage addition. I’m hanging 5/8” on a ceiling that is 16’x30’ with the strapping (16” oc) running parallel with the 16’ side. My thought was to run a pattern of a 12’ sheet then take a 8’ and cut it in half, then the next row...

The gun is brand new, fresh out the box. The compressor feeds a copper line that branches off to two routes. Each route has a ball valve that remains closed when not in use incase the qd's leak. On the route I was on is about 70ft of hard copper pipe from the compressor to the wall where a...

No load it spins fine. It spins faster than any gun I've used. It took the lug nuts off pretty darn quick.

I'll have to go measure the fitting and copper hard pipe of the air system. My grandfather installed it before I was even a thought. It has never been an issue before but the 2135ti consumes the most air out of many tool we use.

I honestly have no idea what the size of the fitting is, that could be the problem I guess. I'll have to see if I can figure that out. Its just the same size that all of our tools use.

I held it on the bolt for a while, long enough that the socket was getting warm. The compressor has been in the shop longer than I have been alive (29yrs). It could be the compressor, but its a big horizontal tank and it would take a good 15-20 second burst before it would kick on. All the...

I used my new 2135 timax for the first time last weekend to remove the rear calipers on my 2003 sierra. At first I tried setting the regulator to 90 psi and got no luck. I kept increasing the air pressure to 120 and still no luck. I had to resort to a 1/2 breaker bar and a pipe. Granted the...

The garage was supposed to have a 9' and a 15' door on a 30' face so it would have 2' on either side. I would shift the door to the outside so they would poor a 12" section. That way the doors would be the same offset from the outside walls