Search results

whats everyone using for a regulator at the spray gun? Looking for something that may have up to 60psi coming in. the cheapy inline regulators are not much better than pinching the hose,more of a restrictor vs a regulator.

I just picked up an off shore floor stand drill press. Actually not a bad deal for $75. Its got a brand new 3/4 chuck on it,.marked JT-3 the nameplate on drill,says spindle is an MT-3 My other drill press (Delta/Rockwell made in USA) has a chuck I replaced with a 5/8 grizzly and is marked JT-33...

Some may remember the nutsert tool I made for 1/4" and larger nutserts. I used a hydraulic conduit knock out cutter and it works great. I have several smaller ones I need to set(mainly 10/24 and 8/32) using aluminum nutserts. Ive had terrible luck with the Horrible Fright ones,went thru 2 of the...

Ive used these because they are made in USA,good quality etc. But now at $1 each,looking for a good quality replacement.

Every time I went to use my new Lincoln auto dark lens. so I did this... Container is a box that held fuses. I simply velcroed it to the inside of hood,out of the way. I keep the loaded battery holder inside,as well as a couple of spares. If I dont plan on using it for a while,I pull the...

So I just purchased a Kobalt 24v impact driver,because I needed the 24v battery pack and charger to repower my Warn Pullzall. It was cheaper to buy the kit than just a battery and charger. This was a tough decision,not from a cost angle,but adding to the madness of tools vs brands. Back from the...

Warn pullzall I think the OEMs were NiCad. OEM is around $150 ea. anyway I have 1 thats shot and the other is weak. Took it to the local Interstate battery for a rebuild quote. $100 and replacement batteries(sub C cell) were lower mAh (OEM is 2500). I looked at buying the Sub Cs myself and...

why no standardization ? Everyones off doing their own thing. I recently bought a DeWalt oscillating multitool to compliment my corded Dremel one.The new tool came with a cutter blade(doesnt say anything about what it can cut) and an adapter. So I pulled out the Dremel to see what attachments...

whats everyone using for hardner for the oil based Rustoleum? I ususally go to the auto body paint store and buy universal hardner,but now looking for something I can pick up at tractor supply,walmart,NAPA etc.

I cant believe that such a large expensive compressor has such a rinky dink air cleaner. Compressor is an 80 gal 2 stage 6.5 HP. Does anyone make a filter that will take auto air cleaner components?

Need some new portaband blades Milwaukee deep cut Ive always used Milwaukee but whats everyone else using,and where to buy?

tried my luck with a 6 inch HF one. I was not prepared for how HORRIBLE the Horrible Fright junk it was. screw on X axis is bent so the only time its easy to use is the last 2 inches of travel. the other side has so much slop that it will move 1/4 inch after you have set it. I wasnt expecting...

Restoring some cast iron and machined steel parts Whats everyone using to duplicate the fresh blasted look? I realize that machined steel and blast cast iron are too different finishes so Im willing to compromise with using the cast iron look. Ive used several types before but threw emptys out...

Has anyone had a problem with a lift in garage and their homeowners insurance? I have a 7000 lb 2 post lift and am changing insurance companies. Just wondering if they add a rider or even cancel due to it?

found these in a drawer that I had hidden from everyone. I used to buy a set when on sale and price was down to $1 a screwdriver.Best part is they are old enough to have been made in USA

and we will be on lockdown starting tomorrow night. This wasnt that old,only used a few times but was cheap($50) so oh well. Last autodark I had was a Daytona Mig with a swedish lens and it lasted 20 yrs until the solar assist would no longer keep the battery up(internal ,non replaceable). So...

I have some 1/8" wall 1" C channel that needs to be welded back to back. I have a couple different spot welders and wonder if this can be done successfully.

what bit has the best luck removal of bellhouse to trans body on the newer 4l60e? I see plenty of failures.

Ive done my share of grinding.. first real entire explosion,not just a chunk or 2. About 45 yrs ago in shop a small piece of grinding disc hit a fellow worker in the eye....he was about 30 ft away. No one wore eye protection then unless they were the one grinding. Today was my lucky day... All...

I need to replace the gun on a Lincoln I bought that was freight damaged. It also took out the female connector body for switch/controls thats inside the machine. So Im looking at replacing the 4 pin connector with a 5 pin Euro style which seems like a much better setup,and then can also use the...