Search results

Hi Everyone, We picked up a 15HP Kaeser 3 phase compressor. Currently i runs only if i push in the contactor on the left it works no problem. See attached photos for both the model and SN, also the contactor. The start button does not work, also once it hits the cycle limit it will not restart...

Hi, I recently purchased a 1961 Washington compressor used. It needs a little well a lot of love. It has a large 200G tank and a massive pump on it. I cannot figure out the make of the pump nor the HP rating. Currently it has a 5HP motor that just seems way too small for it. Any help...

Good afternoon/morning, I just wanted to introduce my new company to many of you who followed my build in Los Angeles & UT. https://www.garagejournal.com/forum/threads/new-southern-ca-modern-garage-house-build.335191/ &...

Hi all, I am looking for someone to do a digital rendering of a shop space showing, lifts, work areas, plasma table, wall cabinets, etc. Need this done pretty quick. I have a shop layout PDF that is a start, just need someone taking it to the 3D level. DM if you can do this. E-Mail -...

Hi all, So this will be our 4th house that i remodeled in the last 7 years. Some of you guys might have followed my thread in CA with the pre-built home we did. However, we moved to UT and bought an older home in a great area against the Wasatch mountain range. We will be redoing the whole...

My wife and i just purchased a new house and the tile is awful and dated. I am going to rip out the tile and replace it with the click together life proof flooring. Generally tile with thin-set is taller then the life proof. Will i have to build up the floor with additional plywood? What is the...

I have a 30x48x24’ pole barn. It is currently uninsulated. I will be doing R13 on walls and r26 on roof area. I used the calculator and it said 11k cooling 18k heat. That seems low, I was thinking a 5ton package unit. Any suggestions? Live in Salt Lake City area. 14x16’ doors on East and West...

This is a new thread/continuation of my thread listed below. Old Thread: https://www.garagejournal.com/forum/showthread.php?t=335191&page=13 We relocated from LA to SLC with the company I work for. After selling our house in Los Angeles we bought a house in the Sandy area of Utah. I started...

Hi All, We will be moving to the Utah area and are looking for a landscape architect as the houses we have been looking at do not have the yard finished. I would like some to bounce some ideas of, of course for a few, and use them in a possible design. They do not have to be local but we...

Hi all, I am moving to the Salt Lake area in Utah. I am in need of RV storage looking for something along the lines of 65' overall. I can separate trailer and rig if needs be. Probably only need it for 6 months or until we find a house or something.

I have a plywood wall that connects the concrete floor and i would like to flash it so i can hose my garage down lightly. Any recommendations. Wall is inside the garage- https://www.garagejournal.com/forum/showpost.php?p=7488927&postcount=223 Looking at something like this-...

I have been looking for ideas on a media closet/area under the stairs for my amp, network switch, etc. I need it to be somewhat dust resistant but still be able to breathe. Any ideas.

For all those parents out there that have Children in the stages of loving trucks, police cars, etc, I highly recommend going to a "Touch a Truck" event. They are put on by the city and usually consist of a little over a dozen vehicles the children can sit in, walk through, push all the buttons...

All, I am putting up structural plywood for the shear wall in my garage. However, instead of putting drywall on top, I wanted to simply paint the plywood. I understand it will not be near the finish level of drywall. However i simply do not have the money nor time for dry walling over 2500sf...

So I am finally ready to do my loft in my garage. It is just getting too cluttered with all the items that need to be in the attic area. However, I cannot seem to find a good location to put my stairs. Should I do a 5' spiral stair or a straight up stair, need ideas. I have them in the middle...

So here is the issue- I currently have 24"D x 10' tall pallet racks in my garage. I have not mounting abilities on the wall. How do i modify the pallet rack to be able to store the smaller items? Need ideas concepts. I tried googling and all i get is what to do with used pallets. I do have...

Has anyone checked this table out or know anything about it besides what is on their website. https://store.langmuirsystems.com/ It looks interesting for someone that is on a tight budget and cannot afford a 10k plasma table.

All, I am in need of everyone's help to solve my storage issue. Currently i have to 42" deep pallet racks in the front of my garage. I need something else for the side of my garage but it cannot be deeper then 24". I am looking at something 10-14' tall. Any suggestions, looking at a narrow...

It seems many of the members on here weld quite frequently. I wanted to see if anyone had any recommendations on getting rid of the slop on my chop saw. It is a 14" saw, and I am using USA made blades, not sure on brand has no markings, could be Chinese made. I see it mainly on cutting 45...

I am about to start wiring my metal building, and everyone notes not to use Romex. I will be eventually furring all walls out with wood for the mezzanine going in. However, I am still pricing everything out Romex, 12/3 MC, 12 THHN in 1/2" EMT. Metal Building- 30'x30'x24'. I will have 3 layers...