Search results

I need a m15-1.50 pitch flat socket head bolt. Any suggestions? These are for the ends of my dumbbell handles. I thought they were 5/8", but they are metric.

I need a m15-1.50 pitch flat socket head bolt. Any suggestions? These are for the ends of my dumbbell handles. I thought they were 5/8", but they are metric.

I would like some advice about my options. I like the sound of cummins 10 year warranty so far, but does anybody know for sure that they are easy to work with. it seams everybody has generac, so Im getting reports everywhere across the board on those. Also it scares me that i see a bunch of used...

I just found the fixture to mount a portable band saw in to use as portable chop saw and upright band saw. It is expensive though. Does anybody else make one. I looked at the swag but that only mounts it to a table. I like having it as a chop saw as well.

I am needing a new(better) table saw. Not immediately, but soon. I have the chance to pick the bosch up @ menards on sale for $499 plus 11% back in a rebate to be used @their store. The Ridgid goes on sale for $299, but I dont know when it will. I am a novice at best woodworker. I want to be...

i aquired one for my in floor heat. the relay, tranformer, and gas valve wiring has been removed. i have looked all day for a wiring diagram. can some one give me a direction to turn. i would like to get this going for this winter.

I am getting tired of fooling with propane tanks so I'm finally working on the gas line to hook up a small space heater and boiler for floor heat. I just measured at the inlet of my shop. I got 5 inches of water column. How does that sound.

Can anyone tell me how to reset one of these PTAC

does anyone know if it would be possible to use a water heater tank as a supplement air tank. i want to plumb in another tank so when i run bigger demand tools sand blaster sander painting ect. i could open a valve and my compressor would fill the supplement tank for more storage. pricing out...

does anyone have eperience on cutting trex decking board w/ a blade other than the freud recomended blade. i feel it is just a gimmick that freud and trex are putting out there but want to see if anyone else has done it with a different blade. i am going to replace the blades in my circular...

i came across a compressor that i cant find any specs on. it has the dayton logo on the tank along with a universal air products sticker. under the pump, it has a sticker that says "dayton air compressor model 5z588 3 hp 1 stage" 3 hp 1 phase. it also has a dayton labeled motor. the pump number...

i got the line dropped and capped off both ends. with one end i used a gauge and schrader valve. i pumped up to 20 psi. it lost 2.5-3 psi over 4 hours. i have submerged all the joints in water/ or sprayed w/ soap water and got no bubbles. is this acceptable.

when i run my conduit for my electric, is there a certain wire for the trace wire or just any 16ga solid core wire suffice.

can a con-stab fitting be removed and re-installed like a shark bite plumbing fitting.

my garage door just starting giving me fits. its a craftman 1/2 hp built in 2006. it would not travel at all. i made all the adjustments ie travel force and distance. nothing but a motor trying to turn sound. i disconnected the chain all together so it had no load what so ever. i got it to turn...

i have a track saw from grizzly wich has been great until recently. after making a cut though 1 sheet of 7/16" osb, it needs to sit a while. it wont react to the trigger at all. is this a brushes issue. i not over stressing the saw cutting osb i would not think.

my plan is to run yellow ips line 1 1/4" i.d. from the meter to the shop 125'. i'm runnng it in conduit. just being extra cautious. ips is not supposed to be in the building i understand, so can i use a transition and connect a length of csst for the last 10 feet to actually come into the...

i picked up one cheap. $15. the shoe is a little tweaked. ereplacementparts.com gets $65 shipped for it. i've used them before and had good service. i'm just wondering if i could save a couple dollars somewhere else.

i have a canarm 56" fan coming. i want to control the speed [B]and[B] direction. there is the Canarm CNFRMC5 Control i can get for $45 to $50. is there an alternative controller.

i have a 135 foot run from my breaker box to my shop. i am going to run it 2 1/2 conduit. my shop box is a homeline 125 20 circuit breaker box. my electrician/buddy said i need #3 copper between the 2 boxes. w/ #6 ground. could a 2-2-2-4 aluminum mobile home feeder replace that.