Search results

Question concerning my house plumbing. I have a well that comes in and T's to a pressure tank and then runs to some filters then to a water softener then to the rest of the house. The line coming from the well is likely 1.25" and then goes down to 1" at the T where it goes to the pressure tank...

I have a split level house (basically 4 levels but one side is two story above, other side is two story with no being a basement) and I am having problems with the toilet in the lower level (Second level over all but basically at ground level). Anyway I have orangeburg pipe as my septic line...

Our water has approx. 4 ppm of iron with the staining and we also have the rotten rgg small at times. Looking for a system to handle these issues. We currently have a water softner so that part is covered. What does everyone use for iron filtration? Sent from my SM-G900R4 using Tapatalk

Looking to get an auto darkening welding helmet. Going to be learning mig and have an old welding helmet but it isn't the right shade as I can't get a good view. So instead of buying a new shade I thought I would try out an auto helmet. I don't have a need for much welding so a cheap starter is...

Looking to add a hayloft in my leanto off my shop. Leanto is 12' deep by 48' wide and 12' opening but the sidewall of the shop is 16'. Looking to build a loft that is 16' wide as the outside support posts are 6' OC and then make it 12' deep. Curious what kind of material I will be looking at to...

Looking into getting a topside creeper. Have a 03 Excursion with a 6.0 and a 04 F250 with a 6.0 that would allow maintenance to be so much easier if I have a topside creeper. Been looking at the Traxion 3-100 and Traxion 3-700 but not sure which to get. From the videos I have seen I may be...

I have the following SK sockets for sale. All these sockets are dirty and used so don't expect anything shiny and new. These are surplus sockets I have from picking up lots at sales. The list is as follows: 3/8" Drive 13mm Deep 12 point 8413 x 8 15mm Deep 12 point 8415 x 7 7/16 shallow 6...

Long story short my brothers house needs all the floor joists under the kitchen replaced due to termite damage. This section will also need to be lifted to straighten it out and re-align everything. Probably needs to go up 6" at the worst spot. My question is can I simply change the direction...

Did a search and had tons of results but not with the answer I am looking for. So perhaps someone has a solution and I just haven't seen it or found it yet. Anyway, I am wanting to run several lines off my compressor but I want to run a whip line from the compressor to a manifold or splitter...

Seen an auction coming up that has a decent looking 2 post lift up for grabs. The lift in question is a Challenger 39000. Tried searching to see what a price range might be but found nothing specific to this lift even though I am guessing a 9000# 2 post lift regardless of brand will probably...

I have a SK 3770 ratchet (3/8 drive, bent handle, flex head) and the head no longer maintains its position and just flops basically. Curious if anyone has dealt with something similar and had a fix for it or just **** it up and deal with it knowing its had plenty of use and paid for itself?

I am looking for the following SK items to complete my setup. Would prefer to not buy SK Wayne as a majority of my stuff is not Wayne but otherwise I will buy new or old. I have PayPal for payment. Sockets 3/8 Drive 6pt shallow SAE 1/4", 5/16, 5/8, 13/16, 7/8, 15/16, 1" 3/8 drive 6 point...

Anybody have experience with this? It is suppose to find shorts and open grounds in automotive applications. I have an 04 F250 with a drain on the battery and curious if this would be a good tool to help find the problem. This is what I am talking about for people who don't know what it is...

Tried a search and got the typical snap on versus everyone else but did not come across much comparison to SK. I'm a SK fan and have used their ratchets for some time but I keep reading how snap on is the best thing with their dual 80 ratchets. I have no one with one to be able to get my hands...

So I forgot to call today and ask this so hoping someone here may know. I have a 220v air compressor hard wired. The switch on the compressor does not work as I broke the plastic cap when hooking up the wiring. Really don't feel like replacing it. So now the air compressor is only controlled...

So I have the following and can't recall its use. Hope someone can refresh my memory. Sent from my SM-G900R4 using Tapatalk

Curious what these are and what they are used for. They were my dad's. I seen some lettering on them but could not make out what it said. I'm clueless and hoping the vast knowledge people have here someone will know. Sent from my SM-G900R4 using Tapatalk

I thought I would show how I mounted the upper cabinets in my pole barn because when I did a search all I could find was information telling people to frame out the space and build it that way, which is probably the correct way but I think mine will work. Anyway, I wanted my cabinets to mount...

I've tried searching with no luck so I'm asking here. I have an air compressor with a rectangular intake port and would like to add a muffler or extend the intake for noise reduction. The intake port can be seen in the attached picture. Don't really feel like fabbing something so i was hoping a...

Hope I used the correct term in the subject line. Anyway, I ran 12/3 around the perimeter of my shop for outlets. I want to use both circuits of the 12/3 and it is my understanding I can pull this off without a gfci breaker by doing the following. First I need a 20 amp double pole breaker then...