Search results

I have a Cayenne 45000 btu heater and I have it hanging from the ceiling but if I run the b-vent out the wall it will be going through the 2x10 header,this is a pole barn style addition. My question is can I run the b-vent from the heater down about 10" and then out the wall,the heater is power...

Just wondering if anyone has a Cayenne heater and how to wire it up,hopefully a few pics,the wiring diagram doesnt show any grey wires and there are 2 of them that need to be hooked up to something? Any help here would be great!!! Thanks Mike:lol_hitti

Just wondering if anyone has any suggestions for hangers for 1/2"sch40 pipe for my gas line to my heater and also 1/2" copper pipe for my air lines. I want to run the gas line right up tight to the ceiling,and the air line just under it about 1". Thanks Mike:beer:

Just wondering what would happen if I painted over floor sealer? Thanks Mike

I had a guy tell me that my gas line from my house to the garage is to small,it is 1/2 od 3/8 id copper tubing and is about 45 feet long then it goes into 1/2" black pipe. I will be running a 45000 btu natural gas overhead heater,my question is will the 1/2" copper be big enough and if not what...

Hi Guys, I live in Canada and Im thinking of ordering a Big Maxx heater from Northern Tool + Equipment. Has anyone ordered one and had it shipped to Canada,and if so did they charge brokers fees,or just the actual shipping cost? Thanks Mike

Well Im debating on buying a big maxx heater but I was wondering would the 45000 btu be cheaper to run than the 75000 btu. The shop I am putting in is 500 square feet,but I also have the front of the garage that I might also want to heat someday,I have a wall between the 2 shops with a 6 foot...

I just finished etching the floor for the second time and it seems pretty good,feels like 100 grit sand paper but there are brown streaks on the floor yet. I power washed it 4 times after I was done etching with the muriatic acid. Is there usually a little brown residue after, and am I ok to...

Im just wondering if you wet the floor first before etching with muriatic acid,or just start with a dry floor? And what do you use to put the acid on the floor,would a garden sprayer work? Thanks Mike

Im just wondering when you can tighten the clamp in an outlet box that clamps on the wire coming into the box,can it be to tight,I just used my cordless drill to tighten them down,but now im wondering if its to tight will it cause problems? Thanks Mike :confused:

I just finished wiring my garage panel and I have all the circuit breakers on just one side of the panel or buss bars,I have one more 50 amp circuit breaker to put in and was going to put it on the other side so there would be a little more room for the #6 wire I will be using. My question is...

I noticed that on my main panel the insulation that covers all the wires doesnt come inside the panel at all,would it really matter if it was in the panel by an inch or so,and how much should there be in an outlet,does it have to be cut back as far as possible.And just curious is this a fire...

I am just getting ready to paint my new addition and was wondering if I need to cover the floor with tarps, because I will be etching the concrete with acid before I seal it and if the acid will remove the paint specs then I wont bother to cover the floor when I paint. What do you guys...

Im thinking about getting the AcryliSeal 3501 to seal my garage floor just wondering if anyone has used it and if you have what do you think about it. Also did you use to prepare the concrete before using the AcryliSeal 3501? Thanks Mike

I have a concern,I just read that you shouldnt use solid wire to wire a machine with you should use stranded wire. I have already ran all my wire and insulated and drywalled over it,but it is 10 gauge solid wire. The motors I will be running are all 3 phase using a rotary phase converter. The...

Ok this is probably a dumb question but I would rather find out now while im building this addition rather than after it is finished. Heres what im needing to know. I have added on to my garage and the old garage is insulated and vapor barriered and so is the new addition,but the wall seperating...

Ok heres my problem,I have just added onto my garage and the wall that separates the old and the new will have a door but I will only be heating one side at a time,either to work on the car sometimes or to work on my machines. What I need to know is what side should the vapor barrier be on or...

Just wondering if anyone has any good ideas for painting the drywall in my garage. I want it to be durable and easy to wipe off as im planning on using it as a small machine shop and coolant and oil are probably going to splash on it. Thanks Mike

Where can I buy the waterbased AcryliSeal 3501? Thanks Mike

Well I put my new addition up and I was looking down the side of the garage and noticed that its not perfectly straight. So I ran a string from end to end which is 46 feet long and its out about 1-1/4" and it seems mainly to be right where the new addition meets the old garage that its the...