Search results

We already got this for your current one. https://www.garagejournal.com/forum/threads/lets-see-your-toolbox.466/ I know I stepped up at least 3-4 times, and I bet others have too.

I thought this would be a good thread since the similar MAC thread is doing well. especially interested in Matco stuff that is better than SnapOn - and IIRC, some like the Matco locking flex ratchet lock buttons/mechanism better also, aren't some Matco ratchet heads thinner than Snappie?

Steel gauge, ball bearings or roller bearings for the drawers, etc. - What is needed? I thought this would be a good topic since we have a LOT of box threads but no over view of what makes a box a good box...

Looking at the HF, Snappy, Hazet, Craftsman and other threads made me wonder what they do in Japan for car repair tool storage. I say car repair to avoid the beauty pics of their carpenters tool boxes. Based on the ratchets and wrenches I own or have seen, they must have some high quality...

The 8 series are 30 tooth. Anybody know when they started?

any ideas on what to get? I think they measure this in sones...

I'll start... Ever since I joined GJ my tool purchases have gone way up. I can afford it but it might get me kicked out of the Church of Scotland. Suddenly all my SnapOn ratchet handles were obsolete, and I discovered I needed a whole bunch of special wrenches too. I realized my screwdrivers...

Where would be the easiest place to find a run about 8 ft. long of U channel material? I'm looking for the cross-sectional sizes to be about 3" and I need a flange on it so I can screw it to a wall. Thanks!

I'm getting a plumber to run some pex to give me a faucet (hose bib) on the 2nd story deck on my house. Pex needs to have sunlight blocked or it falls apart. I'd like to use a "U" shaped cross-section of patterned trim board, which I could paint to match the corner boards on the house. But I...

I'm curious when Snapon started making the 8-series ratchets, like the F830 which are 30 teeth inside?

When did Snap On start making Dual-80 ratchets? Was it 2009?

What would be the best way to repair gaps like this in my bathroom? The tile sits on top of an electric radiant heat pad and is 15-20 years old. Thanks!

Alloy Artifacts says P&C was started in the 1920s, then became a subsidiary of Plomb Tool (later Proto). It was acquired by the Plomb Tool Company of Los Angeles in 1941, but they don't say if they continued using the original trademark to stamp the tools. It folded in 1960. I am wondering if...

Anybody know anything about them? I don't need more screwdrivers, but... I saw a nice looking "Nanch Small Precision Screwdriver Set" on Amerzon for $22, so... I can return it if it *****.:scared:

Ideas on a quality brand? I just need a 10 mm - nothing else. Snappy is too spendy. Armstong seems dead; not a fan of HF or Gearwrench Facom, KTC, Tone(?) - not sure what is out there as searches keep bring up non-flex head (fixed head) wrenches Thx.

I couldn't find a thread for the older Snap-On stickers or postcards, so I thought I'd start one... Post 'em up:pimpflash

need to cut out some bamboo stalks I have an old corded Milwaukee Sawzall - what's the best blade? red Diablo pruning blade with the carbide teeth? or will the big teeth catch on the stalk and just wave back & forth?

I lost my one sticker and the shiny wrench on rusty nut postcard too, but I still thought this would be a good thread...

How bad are those little $300 Craftsman cabinets? like this: https://www.craftsman.com/products/storage-garage/tool-storage/tool-chests/cmst98223rb--2000-series-37-in-5-drawer-rolling-tool-cabinet

needs to drill 5 cm deep into rock must operate 30 times without failure must operate at about -81 degrees F but maybe down to -220 degrees F should not weigh too much as it will need to be moved to a remote job site