Search results

I got this on amazon that was supposed to spray properly. It does spray w/o the extended hose but when I put on the hose w/ 4 holes on the perimeter of the nozzle is sprays strongly out of 1 and weak out of another. Two others it doesn't even spray out of so I have no idea if it's actually...

My sister put in a single drain sink. I put in a p trap for now but the bottom fitting is currently a slip fit which has very little material to allow sealing and isn't the right way to do it. I need slip fit into the disposal and into the home drain pipe and threaded coupling at the bottom...

I purchased a 6.5" fuel circular saw. The motor is LOUD. Louder than any fuel tool I've ever used. The switch is also different feeling than any other Milwaukee fuel tool I have and I have a lot. That could be because the cir. saw needs on/off and no linearity but I don't know. My first cir...

I know code requires the gas dryer to be 16" off the floor in a garage but i never bothered to make a podium for them. Well wifey decided she wanted a front load washer and loading it is a pain so I finally made a podium. However, in doing this, I had to remove the wire shelf on the back wall...

My sister just bought a house and it has a water-right impression plus softener. HOWEVER, there is no brine tank. Looking at the head, I have to assume this a plug of some sort for where the brine tank hose would be. Is there any logical reason the previous owner would have removed the brine...

Googling rubber ******* didn't help me any. Closest thing I could find was CPU fan isolating ******* but they OD was way too small. I'd 3D print something but I don't have a material durable enough to stay together being pulled as much as these would be. Anyone have any idea where I can find...

I have many of these of these same 110V AC COB LEDS retrofitted into a about 10 outside fixtures. They are not exposed to water and are always dry. I have one position that over the last few months is going through a COB LED every week or so. Every other fixture is fine. The COB just gets...

So I have this battery which is 650CCA yet shows 60Ah. From the conversions I've seen it should be CCA \ 7.25 or 89.6Ah but the battery label shows otherwise. I also looked an official AC Delco spec page and it also shows this as correct. The reason I'm even asking this is because a battery...

I am having to replace a gravity feed tube on my RV. The ID is corrugated. The fittings on either side are barbs. There is no sealant on this and I'm sort of at a loss how I can achieve a watertight seal w/ a corrugated ID and a barb using a hose clamp. The manual states that you can fill...

I've been trying to figure out the equation but I'm failing. I have to support the back off a fresh water tank for my RV. The tube will be sitting atop frame rails and under the floor the tank sits on. I am unsure of the size of the tank so I am going with the largest it can be (100g) so...

Hey guys I have a HF predator that runs well. Idles great, etc. I don't know if this was the case before but when exercising it today (It sits most the time) i noticed anything above 1100W of load it was bogging down. I checked the RPM and sure enough it was around 3440 at 2K watts. I went...

I have a BILT helmet (Made for cycle gear here in Illinois) that is about 3 years old. The visor is no longer obtainable (New or used) and this helmet has sentimental value to me and I'd like to continue using it. One of the lexan ******* that rides in a detent to hold the visor up has...

Basically, I did what I thought would be a lasting repair a few years back. I used well nuts (Expanding rubber) and they worked, even though they are not exactly intended for this use case. The ladder is thin alum. tube and unfortunately (likely due to the cold of winter) the expanding force...

She had a friend do a bathroom remodel for her. He's a tile setter, not a plumber. I noticed this drains VERY slowly and too slow to use it for more than maybe 1 minute. I went into the crawl space and found this. I also see he notched the top 1/2 of the floor joist to pass this PVC...

I have an AC motor that i've been limping along for some time. Universal Electric Co. JA2M194N I've disassembled it, cleaned the bushings, etc. but the bushings are just at the end of life. The motor is a 1500RPM 3.3" motor with a 2.25" exposed 5/16" shaft and it spins (Clockwise shaft end...

I'm trying to wrap my head about the construction of this garage soffit area. Basically there is double 6 eave panels boxed in with 1x8 fascia boards (which hang below the F channel by a good inch) and I'm trying to understand how one can even get soffit panels out without removing the fascia...

A garage was added to this house and that second roof tied into the bottom roof is part of that addition. I am getting water behind my fascia where my gutter screws into and the wood is rotted there as well. I assume water is running down the roof and under the side panel and rotting the wood...

From the factory they gooped the **** out of the grommet (seal) to tank and the grommet to pipe connections w/ silicon sealant. The fit is tight and it's a rubber seal so I would assume it would do it's just fine by being installed dry but curious if they know something I don't? I have the...

I decided to replace my toilet and this turned into pulling the old tile floor as the new toilet would not cover the footprint of the old toilet. Originally there were 1" hex tiles down before and grout but I'm considering going laminate flooring. Either peel and stick or perhaps laminate...

This is an AWD Lexus 05 RX330. Never seen this before. Basically what is occurring is the inner race on the backside (In relation to the way the hub is pressed in) is pressing out as the hub is pressed in. I did the other side a few years ago and had no issues. It doesn't seem to be...