Search results

Building a mez in my shop and plan on having it 10x30 foot. The 30 will be running along an outside wall. Question is how far apart can the inside supports be? Not wanting a wall on the inside part. One side of the 30 will be attached to outside wall and 10 foot across from that I will need...

Getting ready to insulate my metal pole building. It's 42x72x16. I have a quote for rolled batts of unfaced fiberglass. Should I put plastic on outside walls before I put the stuff in and also what is best way to hold it in place? It is 48 inches wide, so I will need two pieces plus an extra...

Bought a new trailer and want to seal the osb walls and floor. Whats the best product to seal it with? Want a clear Thank you

Long time no post. I have a 42x72 pole building. I had 5 inches of concrete poured. I would like to add a second floor. Will the concrete be sufficient to support the post? I have in floor heat and hate to have to cut it out to pour more concrete. Thank you

Well after a long time getting ready to epoxy floor. It looks like ****. Gas outs all over. Primer was a waste I guess. I can get pics to work as usual. If you want to seevth I can email somebody and they can post

I have extra gloss sealer. can I use my wagoner to spray the left over and help eliminate some of the roller texture? Still in the 24 hour application window.

Building a second floor in shop. First part will be 42x12. One wall is the outside wall running the 42 span. Have an overhead door on one end. What size wood supports do I need and is 16 centers good. Thinking a 2x8 across back wall. Its a pole building and there is 9 foot centers. Would...

Going to paint my floor finally. The epoxy has a pot life of 1/2 hour. Do I need to change rollers every batch also or will one roller do the whole floor without getting hard?

will this heater work in a 3,000 s/f morton building with no insulation and 16 ft. walls? trying to get floor temp up enough to epoxy. the unit is the 200,000 btu one. says it is good to over 4,000 s/f. i assume that is low walls and insulated. not sure if i can use this one or need the...

Looking at a 175,000 torpedo unit. I have 2911 s/f. It is good for 4,000. They have a 165,000 that is good for 3,000. I have 16' walls so figure better chance with the bigger one. Can a gas grille tank be used? Will it last more than a few minutes? Just wanting to heat shop enough to lay...

Can the silkflex be ground. I plan to use some and since it takes 7 days to cure. I am going to grind my floor one more time with a big grinder. It was done once and I have logged 120 plus hours with a 7 inch wheel getting what the big one didn't get. A lot of low spots. I have knocked the...

Is there much of a difference in the final finish between these two? Using the blue one now.

Been using the ridgid 7 inch grinding wheel. The surface felt smooth. I looked up pics of csp. Mine looks close to a 2. I would say the surface of a cardboard box. I have been told by a good source that is ok. After looking at pics I'm worried again now

Tried to acid etch today. Whatever the dark low spots are, acid won't touch it. Even went pure. Got a 4 1/2 diamond cup and it even had trouble getting it. Wish the big grinder could have got it

I would like to say thank you to Scotty and crew. I have asked a million questions and have been answered with respect and politeness. I am sure I have been annoying. Also would like to point out that ruger lady was right there for me also. I had already basically decided on legacy when I got...

What would be black in the mix. Looks like little piece of coal. Not brittle. Same size as the rocks. I can't post a pic. I can text one if somebodyelse wants to

I oreded my epoxy package today. I forgot to order seam seal and stuff to repair the popouts. Any box store stuff work? Thank you

I am scared on what to do with my floor. I was sold on epoxy and got a nice set up quoted from legacy. Then I hear bad stuff about epoxy and then think maybe vct. Then here bad about it. I want the epoxy look, but if it has issues within the first year or so, I will have a useless building. I...

Ok . Can waves that spread out over 6 feet be smoothed? Assume anything wider than grinder itself wont be able to get perfectly straight, unless i put some kind of outriggers on grinder to keep flat over a wider area. Took a 6 foot level and can see some daylight in places. If they can't I...

Got paid by contractor to have floor ground. Have a few pop outs to take care of then an epoxy. Any specials for forum members?