Search results

I just bought a Quick Jack 5000 unit from Costco online. It should be coming next week. The Quick Jack hydraulic lift doesn’t come with the needed fluid because it would a hazmat thing and they would end up charging quite a bit more. No biggie. They forwarded some info on the unit and there are...

https://www.costco.com/QuickJack-5%2c000-LB-Capacity-Portable-Car-Lift.product.100460313.html This was $999.99 on New Year’s Day. It regularly sells for 1099.99. Does anyone have any insider info on when this might go back to $999.99? Thanks in advance.

This chuck is brand new and has never been used and has not been inserted into a machine. I am selling it because I ended up not getting a milling machine with an R8 spindle. I chose this chuck because the R8 taper is an integral part of the chuck and because the runout is the lowest available...

I am strongly considering installing a free flow tile. I am leaning towards Swisstrax. What dealer has the best pricing for this tile? Thank you for your help.

I just replaced our humidifier because of a faulty solenoid valve. HVAC comoany just gave me a whole unit since they were really busy. Luckily it was under warranty. After the swap, I tested the unit and the circuit board was calling for the solenoid valve to open but it wouldn’t. It failed...

https://www.lowes.com/pd/Kobalt-Multi-Purpose-Air-Tank/50126548 I have this kobalt air tank and there is a one way valve between the male quick input fitting and the manifold. Seems like this has failed. The easy solution is to replace that with a ball valve. But what is this thing called...

Has anyone taken an air hose reel and converted it to an electric reel? I know that Cox Reels and Reelcraft offer these electric cord reels but @$300-$500, I thought it should be doable to roll your own. https://www.northerntool.com/shop/tools/product_200317266_200317266 I have a Goodyear...

Here are the final details on this Norseman Garage Journal offer: No limits on these specific items; buy what you want, as much as you want. This Garage Journal offer begins Friday 10/26/2018 and will end on Friday November 2, 2018 at 2PM Eastern Standard Time These Norseman bits are proudly...

Here are the final details on this Norseman Garage Journal offer: No limits on these specific items; buy what you want, as much as you want. This Garage Journal offer begins Friday 10/26/2018 and will end on Friday November 2, 2018 at 2PM Eastern Standard Time These Norseman bits are proudly...

Here are the final details on this Norseman Garage Journal offer: No limits on these specific items; buy what you want, as much as you want. This Garage Journal offer begins Friday 10/26/2018 and will end on Friday November 2, 2018 at 2PM Eastern Standard Time These Norseman bits are proudly...

I have been able to put together a few group buys for Norseman drill products in years past. With these past promotions, all products from Norseman were offered at discounted prices. I have been contacted over the past months and see that there is some interest in folks wanting to buy Norseman...

Does current code allow for a grounding lug to have 2 ground wires attached to it? Grounding lug like this: https://www.homedepot.com/p/Blackburn-2-to-14-Dual-Rated-Mechanical-Connector-with-Single-Conductor-Mount-2-Pack-ADR2-B2-5/100206198 If not could one wire go into intended slot with set...

I need to mount a piece of wood to the wall to mount electrical outlets, motor switches and a rotary phase converter panel. The easiest way because of space would be to put this 3/4 plywood over the 120v outlet. I need to pull this 120v wiring through the plywood and into the back of a surface...

I will be wiring up a commercial rotary phase converter. Here is some pertinent information about my setup. 240v input power: 50 amp breaker with 6 gauge wire (currently wired as a dryer plug, so 4 wires at this location. Plug is on interior attached garage wall and was installed by builder...

I really need a 23 mm crowfoot wrench. This seems to be as rare as a purple unicorn. Can’t readily find it in town. Snap on truck can order it but it will probably take half a week. 15/16 is fairly close. 23mm is .9055 and 15/16 is .9375. I’m wondering if I bought a 15/16 crowfoot would it work...

I want to add lighting to a knee mill. What do you use? Incandescent light with LED bulb will work fine for me. Saw this from msc. Was hoping to find something cheaper. https://www.mscdirect.com/product/details/85607265?fromRR=Y

I need to create and electrical panel for my milling machine. This will mount on the machine on the back or side and will supply power to dro, powerfeeds, light. I want to have a switch and was thinking that having a simple on and off selector switch mounted near the mill’s fwd/off/rev switch...

https://www.lowes.com/b/craftsman.html?cm_mmc=email_promo-_-20180401-_-lm_214984-_-banr_craftman&et_rid=3094416&et_cid=214984 Probably someone posted here prior to this. If that’s the case, please delete this.

I am going to be needing a single phase 240 v disconnect switch. This will only be used in the event of an emergency. I have a 240v circuit in my attached garage. 50 amp breaker is in panel on side of house. This switch will be installed in case I need to shut down the circuit and won’t need to...

https://www.homedepot.com/p/California-Air-Tools-10-Gal-2-0-HP-Ultra-Quiet-and-Oil-Free-Electric-Air-Compressor-10020C/206644539 10 gallon 2.0HP $245 Pretty good deal.