Search results

Held my nose and pulled the trigger haha. Gimbal bearing puller, alignment and installation tool set. $126 out the door vs $353 for similar (same style of tools) USA made and CNC cut set. As much as I wanted and preferred the USA made set I just couldn't justify the price for a set of tools...

So wife's car has a pretty bad oil leak which I haven't had any luck tracking down. Ordered a UV flashlight and dye should be here tomorrow going to try to sort it out. Hopefully valve cover and not one of the two oil pans, which will probably mean pulling motor again... I went back and forth...

Need to raise some cash so posting some more tools up for sale. Zelle (Preferred) or PayPal (F&F appreciated) only please. Will ship within the Continental United States Only within one business day of payment. Please PM me with any questions or if you need additional information. Thank you...

Sorry this is home system not garage but I know you guys will steer me in right direction. Concerned about gas fired boiler probably hasn't been serviced properly since it was installed (probably 20+ years ago) and I see some troubling signs just wanted to get your input. 1. Corrosion under...

Don't want to sell these but need to raise some cash. Zelle (preferred) or PayPal (F&F Appreciated) only. All sales final no returns or exchanges. Will ship within the Continental United States within one business day of payment. Thank you! All in excellent working condition no owner marks...

Black nylon cover for KRA4114/KRA4107 or similar tool boxes. Measures approx 40w X 20d X 52h. Zippers and cover are in good working condition hardly ever used. $130 shipped via USPS Med Flat Rate Box within the Continental United States. This has been cross posted on Ebay. Zelle (preferred)...

Wife's car had some issues starting this morning had to check battery, which is in trunk under some panels. There are a couple of plastic retainers that thread onto some studs that are attached to the floor pan. The retainers have a triangular shaped hole that can just be pryed off if...

Going through some roughneck bins in the garage found this old Bonney Alligator wrench and an old Albrecht chuck. Chuck has a bit of surface rust on it but operates very smoothly. It has a collar soaking in some rust solution but no arbor. It's a model 0-378 made in Germany. Don't recall...

Posting up some llightly used air tools I just checked that they are all working but most have been sitting in my box unused for many years so can't guarantee they won't need new seals etc. All are in very good to excellent condition (aside from potential worn seals) and have extremely low use...

Will only accept Zelle (preferred) or PayPal (F&F Appreciated) for these. Shipping within the Continental United States Only (sorry but I'm not equipped to ship outside Continental US). Will ship within one business day of payment. Thank you! 1. SOLD SNAP ON 11 pc 6 PT 1/2" Drive shallow...

Will only accept Zelle (preferred) or PayPal (F&F appreciated) for these items. All sales final no returns or exchanges. Shipping via USPS Flat Rate or UPS Ground within the Continental United States only (sorry I'm not equipped to ship outside Continental US). Will ship within next business...

Have opportunity to possibly do some diag work and repair issue with convertible top on 2003 Ferrari 360 Spider. Only problem is its 2-1/2 hrs drive and I'm not sure if my Autel will communicate with it. To my surprise it seems to have the correct menus. Unfortunately don't have access to...

My FIL had this small Mig welder don't know much about it. Was curious if it still worked wire feeds gas may be leaking a bit but seems to work. I tried a small test weld and kept getting a spark and wire would break off. The spool did seem to be rusted a little may need new wire and possibly...

Replaced battery in MIL's 16kw Generac generator. Old one was badly corroded, esp negative terminal. I cleaned up terminals as best I could and installed new battery. Generator wouldn't start. The terminals looked fine but I cut them off and installed two universal battery connectors and it...

Bringing home and old Matco 26" roll cab (probably 1980s) that I had at a friend's house. There is a center drawer at top that is double deep. When I try to close it it springs back open. Probably has something to do with the lock but I'm not sure. Any ideas appreciated. I have the...

Amazon "lightening" deal 20% off plus a $30 coupon. TS508WF with eight MX Sensors $305 including tax and free shipping. I bought a used set of wheels for my F150 with no sensors so light is on. Going to order new tires so I'll have sensors installed when they come in. I think Mavis said $80...

*** SOLD *** Recently purchase and paid $2,160 some unexpected expenses came up and need to sell. Just posting here in case anybody is interested will cross post on ebay with more pics. Used on one project, works great near mint condition includes original packaging and manual. Works with...

Hey guys sorry for new thread. I'm trying to turn a Wilton Vise into a new set of tires and could use your opinions and help. I've posted this vise in before including classifieds and on ebay with not much interest. Well ebay had almost 900 views and 28 followers but not much interest in...

** DONE ** Recently dismantled, stripped and repainted Rustoleum Hammered Verde. Small gouge in flat anvil surface so I painted vs taking off too much metal. Excellent working condition but has usual nicks and scratches from normal use. Handle and screw straight and turns easily both...

Few quick questions that I'm sure have been asked and answered 1000x so apologies in advance. Updating switches, dimmers and outlets in my MIL house which was built mid 1970s. Small metal boxes for the most part. I believe the wiring is 12GA but it seems much thicker and stronger than the 12...