Search results

75 through 95xt and 435 through 465 Case. All glass version

Made outnof recycled wrecker boom, built it three years ago. Just got a valve body update and a extension welded into top to bottom loft a beam at 20’ with no overhead clearence If using it at lower heights foot can be set on ground and used to lift a lot with boom/winch/extension Have to be...

Lot of work cause I wanna be a lazy man and not jump out of machine to adjust forks and wife give me death stare when she has to wrestle with them. $70 each new rams with 18.375 travel. Took my mast and did some work to it Almost touch at close and goes full 47” to edge of mast. You could...

Located just southwest of Chicago. New lift showed up today, so old is for sale 10 years old, 83” wide runways but setup you can drive a dually on it with outer duals hanging off. We did it daily Platforms 20’ long + ramps Newer power unit 1 bridge jack 4 years ago, other one replaced 2 years...

New holland skidsteer tilt pin bore on the attachment plate. The non bushing part always wears on these. New holland wants you to replace the plate which is well over a grand for a bare plate now a days. So welcome to hillrod repair 101. This is a 200 series machine, 100’s are similar. 2”...

Made sure I didn’t say ****** as some People might get bent out of shape about the gender nuetral shift juice now required Anyways, what do you guys have and why? My two stage Lower half air gray jack sure smokes my otc one I have as a secondary. Not even in same ballpark as quality Only...

Somebody asked recently about this in free parking. Taller in height than my typical working bench, heights great as long as objects not stupid heavy Wrap around lip keeps part on it easily so nothing gets away Slight pitch to center, has offset center drain with its own falling drain...

Of the three sets of quick attach forks I own none will sit flat on the ground at boom down on the modified new holland so, this set was the easiest to modify as it’s basically a mast with a center open quick attach bolted to it. Needs the plate raised 2”. Hour with the torch and grinder and...

Have a jib crane in shop that I will load to 1 ton when being careful. Use it so much, and for such wide uses that I keep adding new slings, spreaders, specialty chains and straps to it. Nice part is all my chains, Clevis, straps, and other mosc lifting or chaining devices are all in one spot...

Life got in way and super busy but finnaly got my 30k two post project going. Floor at 6” was not adequate for floor so saw cut to specs Of course hit building power feed with concrete saw so a few grand redoing that overhead and a junction box. Jib crane for between wall and one side of two...

Looking for a 2 part urethane adhesives that dries without presence of air Needs to adhere to steel, if it adheres to rubber also good Needs to be has some flexibility to it, stiff, but not rigid Look up on 3m products site and there is so many part numbers it’s confusing Probably need 12-18...

So I have 80 32’ white pop barn sheets I got for free Going to use it as the ceiling In The remodeled shop. It’s cleary’s better tin, about 8 years old. Was the roof on neighbors building, got minor hail damage and ins paid to replace it all. The hail damage I have no worry’s on, the problem...

Took this down three years ago, got it for free but had one week to get it out No brand, 10’ tall, 36’x47’ Took it down in a day and hauled it away the next, stored it next to the semi it it’s own leanto till now Place is on hill with all the current buildings at top of hill, so everything...

What are you guys using to save rotted off Posts? Buildings been rettined once but now poles all shot Poles Measure a true 6”. Anybody have a solution other than our home brew idea that we are going to try? Plan is to sleeve them in 20” metal at the base, weld rebar sticking out 3 directions...

What’s a good option for a magnetic portable slug cutter style drill? Want to be under 30lbs if I can, 110, portable, and be able to move lever from one side to other for clearance Needs minimum 1.5” throw Have used the **** out of a magtech USA made, Looks like Jancy now owns them. Have the...

What’s people’s general thoughts on house building right now? Have a plan drawn up, 80 acre property with a crappy house on it that’s set for demo is bought Will county Illinois Wait to see how this all plays out or move forewards? Can’t even get some of the permits I need right now with...

Cut the end off our industrial hoist years ago and welded a plate set onto it with multiple angle holes. A box tube then goes in it so you can change your pitch or extension with the hole drill set Today I pinned our engine stand head into the end to front lift a duramax engine out of a van...

Free arrow shop press. Is beatup and kinda haggard. Was given to me free for the air jack for my twin to it So free shop press minus jack, install your own bottle jack and your in business. South of i80 ten miles along the i57 corridor. Can load in a pickup or trailer for you. If you feel...

Friend needs to liquidate. Looks like this gonna be a $500 option. Age unknown, works, air over hydro. Tag doesn’t list a model that’s readible Any idea on exact model number? At $500 it’s a no brained but what’s it worth in used market? Then any idea in weight? Gauge reads up to 150 ton...

Trying to get my $500 jumper 33ha going. Got my repower running temp to do some tests but now have it disabled as I’m intergrating the jlg wiring to the engine to make it function correctly Any idea what my 4 non labeled switches are for? Assuming one of rockers is throttle, the push button...