Search results

Please share your pics of machinery dollies you have made with offset casters...in other words the caster sits outside the frame, and the frame rides low. Looking for ideas, thanks Sent from my iPhone using Tapatalk Pro

I’ve got some pipe to cut ...to use as a brace on an inside corner of a frame. I’m cutting this on a Horizontal bandsaw. Opposite 45s on each end of the pipe. It’s not a problem on angle or square tube, cause the vise lines up the sides, and that cuts are indexed correctly. Is there a...

Can anyone recommend a good magnetic sweep, where the magnet turns off. I am looking for a smaller one to clean up around drill press and welding table. Not the kind that you sweep the floor with. Thanks Sent from my iPhone using Tapatalk Pro

Do different brands of mag drills use proprietary cutters? Or is there a standard? In other words, does jandy only use jandy cutters, hougen only use hougen cutters, etc? Thx Sent from my iPad using Tapatalk Pro

Who makes a good sawzall blade for cutting metal? Sent from my iPhone using Tapatalk Pro

These squares sure make life easier[emoji4] Sent from my iPhone using Tapatalk Pro

I’m going to run a small drain pipe through my garage wall to the exterior. This is for the compressor and air dryer. Is it best to cut the sheet rock, and strap the pipe to a stud, or is there another way to fix it without cutting the sheet rock? Thx Sent from my iPhone using Tapatalk Pro

Anybody recognize this and know the model number? Thanks Sent from my iPhone using Tapatalk Pro

Anybody know of a source for a flanged round stock that is solid and looks like this bushing? Need in in steel and solid without the hollow... making some acorn clamps...I don’t have a lathe and don’t want to spend a lot having them machined them from round stock Thanks Sent from my iPhone...

Anyone use these? Are they chinese? Seems to be a lot cheaper than bessey Sent from my iPhone using Tapatalk Pro

Anyone have one of these? What’s a good, reliable brand? Sent from my iPhone using Tapatalk Pro

So I’m scratching my head on this one. I have an IR D42 dryer and the fan doesn’t run. If I test input power at the female connection there is 120 volts, but when the fan is connected it does not run. So I thought I had a bad fan motor. Took the motor out and tested it on 120 and it runs...

Hello, I’m looking for ideas on casters and leveling feet for a welding table. The table weighs about 1800 pounds and is 6x3. Open to any suggestions, like caster size, size of leveling bolts and footers, etc. Pictures would be great if you have some. Thanks Sent from my iPhone using...

Anyone using one of these? I have an IR that has crapped out twice in the past year, and don't want to spend 450 to get it fixed again Sent from my iPhone using Tapatalk Pro

I just got a Parker air pressure regulator hooked up today and it howls and you can feel vibration when you put your hand on it... this occurs only with flow through the regulator. Inlet pressure is 175 and regulator set to 110. Regulator is good 250 psi. This is a new old stock item off...

How good is this for cutting metal? Or is it mainly for wood? Sent from my iPhone using Tapatalk Pro

Who has one? Are you happy with it, or wish you had gone bigger? Sent from my iPhone using Tapatalk Pro

I need to get some transfer punches, what type do you recommend? Some of this will be on fairly thin sheetmeal Thanks Sent from my iPhone using Tapatalk Pro

Which companies still make compressor pumps in USA ? Champion, Saylor Beal, Quincy, Eaton? Sent from my iPhone using Tapatalk Pro

I am setting up a new motor on my compressor with a sheave and bushing. The pump flywheel is pressed on, so depth on the shaft is not adjustable.... any tricks to setting the sheave depth on the motor shaft, so the belts line up? Other than trial and error and eyeballing it?