Search results

I discovered that during the winter, the condenser (Trane) for the home central air was damaged. Two adjacent coils were pinched by about 60% but not punctured. System turns on ok. I was wonder what effect this will have on the systems cooling efficiency. Thanks.... David

The outside unit of my 5 year old Lenox AC has started making an unusual sound. While running, it sounds like it is "hunting" for the right speed. It is a single speed unit. It's cooling the house but also seems to run for a long time between cycles. But again it's been hot here in NJ. Thanks...

I'm looking for a good drop light for the garage. Most are too cheap or not very bright. Open to corded or cordless. What are you guys using? Thanks

I know the answer is yes but I'm not sure we're to go from here. I have a Honda EM5000SX backup generator with a manual transfer switch. Has worked great for years powering refreg, well pump, TV, etc. Recently installed a CubetPower BRG1500 AVRLCD UPS for the home theater so the DirecTV receiver...

So I have been following the threads on the Miller 211 eBay fiasco, zoro deals, and which mig welder is best for 120 volts, etc. My situation is a little different. Looking for my first and last mig welder. I have 240 available, and do not plan on traveling with the welder. If you need something...

I installed a T10000R series pool/spa time switch for my pool. I would like to add a DPST panel switch as provided by the interior panel. The issue I have is the knock out does not fit a standard switch. The screw holes do not line up. I've emailed Intermatic but no reply. Local electrical...

I was recently given a Kennedy top and bottom tool box for helping a friend move. Didn't use the box any more and didn't want to move it. They are in good shape with the exception of the top box. The lid stays are broken. I emailed Kennedy but have not received a reply. I was thinking of...

I am in the process of upgrading a Square D Homeline sub panel. Would like a source for good prices on breakers from an online vendor that you guys have used and trust. Thanks....

Good evening all, I am trying to straighten out a rats nest of thermostat wiring by my oil boiler. There a 3 zones. The wiring coming to the zone valves is a mess, connected by a mish mash of wire nuts, twisted and taped connections, etc. I would like to use some type of wiring block to...

I have a 32 year old Vermont Castings fireplace insert. I really like it but one of the decorative fire bricks has cracked and one of the iron grates has warped. I've done a search, here, internet,ect. but without results for new parts. Any ideas of where I could obtain new parts for this...

I wasn't sure if I should post here or electrical, but here goes. I have a 30yr old Vermont Casting fireplace insert with fans. After 29 yrs I managed to break off the speed control knob for it. The control itself plugs into the wall outlet, then the insert plugs into the control. The control...

What are the main differences between the Modis and Solus Snap On scanners? If I hit the lottery I may be tempted to buy one. Thanks

So a couple of weeks ago I asked for advice on replacing the brake lines on my 2004 Tahoe. Thanks to the advice from you guys, a tackled the job with just a few hiccups. I went with the brake line kit from the dealer, $126.00. To my surprise, the lines were coated to prevent rust, imagin that...

I am looking to update the lighting over my new garage workbench. I did a search and with all the information on the topic of general garage lighting, probably miss the information I was looking for. The garage has 101/2 ceilings and the workbench is roughly 7' from the ceiling. The remainder of...

So I've been a member for less then a month and this site has already guided me in the right direction to spend more $ then I planed on in remodeling my garage. Good job guys:thumbup: Now for the practical side. I need a new cordless drill as I burned up my 18 volt Dewalt of 10 years abusing it...

So I'm about to pull the trigger on new flooring. Due to the age and stained condition of the floor, I'm going with the ribbed, flow thru design from one of the supporters of this forum and be done with it. (I haven't yet decided between the two, they have both been very responsive to my...

So I've painted the walls, new lighting, workbench and non pressboard shelving installed. Time for the floor. After reviewing the threads on this forum ( one of the best decisions I've made), I've ordered samples and requested quotes from the suppliers mentioned. I'm looking at the open tiles as...

Hello all. Finishing up a garage remodel (time for an adult garage). Walls painted, new work bench,lighting and real shelves not made of press board. Started looking at this site to get an idea for a replacement bench vise and flooring..the last two things needed. Enjoyed the forums and the...