Search results

I have a hose bib inside my garage on the wall next to the door. It was put inside as it is connected to my water softener for when i wash my cars. Currently i have a expandable hose connected to it, but its starting to be more of a pain. Looking for a more permanent solution. Need at...

Anyone have any mounting ideas for spools of wire? Either wall or above mount. I want to be able to pull the wire when needed, so no peg mounts. Thanks! Sent from my iPhone using Tapatalk Pro

https://quietcoolsystems.com/products/smart-attic-fan/ my garage has a finished ceiling, and some attic space. Has a gable vent on the end. I was looking at adding the above fan to the gable to let out some heat. Just curious if anyone has had any experience with the above and it it...

I have this tire rack, I want to move it to a place in my garage but the studs don’t line up where I want to mount it. What would you do? Run 2x4s on the backside? Weld some flat bar? Get a different rack? Sent from my iPhone using Tapatalk Pro

Well, finishing up my compressor install finally. I have a dual stage 80 gal that is currently set at 145 psi. Have a regulator off that set to around 130psi feeding the full garage. I have a tire machine that I need to feed 125 to.(have a regulator on it going in) Having 130 at all the drops...

I put up a loft in my garage, was debating putting some drywall on it to finish it, but was thinking maybe getting a bunch of posters instead? Flat car parts? May just get some cheap plastic panels? Take some old pallets apart? Street signs? Anyone done anything to their rafters? Sent...

i bought a Bendpack Asymmetric lift, first one that i have ever used. I am use to the typical centered posts. Going to install it soon finally and was looking for placement suggestions. I would typically center in in the space, but since its asymmetric it should be forward more. space im...

I recently started to re-organize my garage and am having issues with a "dead" space that i have. I have some racking that i cannot move, so it is where it is. Im debating to move my toolbox to where the workbench is and vice versa. This will leave me with a tad smaller workbench area, but...

i have a workbench area that i need to get a top for. Was thinking possibly trying to find a piece of stainless of get a stainless restaurant table. i will probably do occasional welding on it, so was thinking just regular steel. thoughts on thickness? materials? pictures? thanks!

i picked up an auto drain for my compressor since i always forget to do it myself. AHow often do you guys have the tank "drain" and for how long? 80gal. https://www.amazon.com/gp/product/B075H8K97T/?tag=atomicindus08-20 also those that run auto drains, where do you drain them too? have a...

i have a very small gap on the sides of my garage doors that i would like to seal off. I want something that can go inside along the door, would have to clear the cable. What has everyone been using? I dont want the seal on the outside.

I dont know many forums for home generators. Anyone? Or if anyone here may know. I have a sub panel in my home that powers a majority of my home. I am looking at a Generac generator. They make a transfer switch that will do the full sub panel at once. Problem is, i need a few circuits...

Anyone have a recommendation on what type of lube to use for the drawer slides? Box has been sitting and the drawers are getting tough to open and close.

I have 15’ ceilings in my garage, and would like to put shelving or some type of storage above where I will have a workbench/tool boxes. Any suggestions? Would be going on the far wall under the 3 windows and above the 2 tall windows Sent from my iPhone using Tapatalk Pro

This past weekend I spent the days putting down Armorpoxy II. I ordered the job on a pallet kit since I had 1700sqft of floor to do , never did receive tracking info from them. Came about a week and a half later. Instructions and videos are somewhat vague, would have though they had...

Thinking of doing some porcelain tile/pavers. On the driveway in one section. Anyone ever do this? Curious how well it holds up outside. Sent from my iPhone using Tapatalk Pro

I have a hunter tire machine, but need to get a balancer. There are a bunch of cheaper units ~$700 that seem to do a good deal of options for mag wheel weight placements. Operate on 120v also. Just curious if anyone here has experiences with them? recommendations? Not for heavy use, just...

building my garage now, and the ceiling will be drywalled. Im debating going recessed can lights in there, but dont know if they will give off enough light compared to 4' strip lights. Anyone else do cans in their garage? pics? regrets? Also anyone know any flush 4' strip lights?

Trying to decide what type to get. Largest vehicle I own is currently a Tundra. The area I have to work with is 22’ wide by 25’ deep. Ceiling is plenty high so that is not an issue. Is there a reason not to get an asymmetric lift? Looking at bendpacks it says it can be used in both...

I want to run some airline in the walls from my compressor to points in the garage. I’ve heard of some plastic airline with fittings. Any reviews? Or just run copper? Thanks! Sent from my iPhone using Tapatalk