Search results

Hi, I want to move my Mitsubishi unit and reinstall at a new location after maybe, 6 months. Besides capping off the 2 flares coming out of the head unit, is there anything special such as purge and fill it with nitrogen? I am not sure oil residue remaining in the coil would absorb moisture...

Has anyone disassembled this type of lift? I am planning to let it go about half way up, take off the runways, tip each end (the H shape) toward the floor and slide the post out. I think the locks won't get in the way going up, please tell me if it is easy to actuate the lock and levers, on the...

I purchased two of these battery to run a motor, I would like to select the second one after it is depleted. Can I use the switch in the second picture? set up question, Is it safe to tie the negative of both batteries together? There is a pigtail for charging on each so I will be charging both...

I used the use rector number 5 but when I switched to tru blu, when I turn pressure up the air will blow pin holes in the sealant and hiss. letting it cure overnight usually is more successful. I took it all apart and use blue devil tape and 100% cure the problem there. When I took it...

Hi, I am using a HVLP gun that holds 1.5 qts, and I have 2x 5 gallon of stain to go through, the lid had a spout on it but pouring the stain every fill is a definite no for me. I also do not have a sprayer that siphon off a bucket. what is an easy device to refill the small HVLP without making...

I have the tool that pull in a new rubber valve stem by leverage, easy. My question is how do you usually remove the old one. I use pliers (dikes?) and cut and tear the rubber apart from inside the rim, the stems are very hardened that is why I replace them, but I thought maybe there is a...

A while ago I replaced the carb on my pressure washer (B&S) with a 3rd party carb, for the most part it is easy to start and run. But I noticed when I pull the trigger the engine seems to surge and I notice the arm going to the butterfly plate is moving back and forth. Does anyone know if the...

These are mine, I don't remember the one on the left is a ferrule puller or not. It's not been opened so I must have just done it with the smaller one, but it looks like it's almost bent already or need another plier to hold the arms. Is the left side one it any good?

I have been using my Weaver balancer with good success on all my vehicles so far. but I'm need to fit large cone for Toyota Tundra and Landcruiser 110mm center. I bought this cone but as you can see it cannot go all the way in. It should be going into the center which is spring loaded with...

Background: The sensors are made by Launch, which the previous set works fine on my Mitsubishi. It emulates the OE Continental sensor I think similar to one used in Chrysler, just saying, the sensor itself is not that obscure. I got another set this time they have revised the sensor, which...

I have the red craftsman multiimter It was problem free for many years. But recently I noticed it would read DC about 1V higher, the battery in low 12V would read 13V, the charger actually go to work, and the number is not settling like you should see on a battery. Do you guys know what is...

Question about the inside clamping tire changers. There are covers but they only cover when holding the wheel by clamping from outside the of the rim. The inside clamping can do a bigger rim always. It has "teeth" on it. I was suggest I could try to attach some rubber pieces, is that a...

Gas seems to disappear down to the piston or something and displaced a similar amount of oil, onto to the floor. ( I don't usually put the fuel in shut position, but I need to now! plus oil change needed next) Can someone tell me how to service this? B&S website below, but not too helpful...

When I use a ODB2 memory saver that supply from (another) battery to the ECU , does that mean the positive battery cable is going to be hot after removing the car battery? I wasn't going to find out the hard way but I would be careful not to sling it somewhere and hit other metal pieces.

BuildPro tmb54738 I am gauging interest about selling mine, has not been used. 47x38 Pick up only

I have a TPMS tool and it can only program their brand sensor, this is common and that's ok. It works great that way. I was just wondering since the tool can plug into the ODB2 and trigger relearn. If I know my car takes 315 mhz and I see a set from Ebay, can I just install them trigger...

Are they supposed to hold the car? The description says you can but I have seen similar stand that says they are only meant to stabilize the car while on a lift. My other question is can this support the oil pan or even lift the engine a little, so I can do the timing belt on a lift on the...

I have a light switch and 2 recessed cans in the ceiling. I have "LED" BR30 in the ceiling I put in a Lutron Caseta dimmer with the remote, operation wise is nice (like a luxury home). Except the LED BR30 buzzes like a fluorescent tube, it's louder at partially dimmed, and I can hear it even...

use oil/lube or not? cut mild steel mostly. seems like oil would make a mess inside.

how to join the two? I believe the OD of the liquid tight conduit can glue into PVC coupler?