Search results

I have blacktop on my garage floor. It is uneven at the door, high on the sides and low in the middle. The gap goes from 0 on the sides to 1-1/4" gap in the middle. That gap is below the existing stock rubber weather stripping on the door. Can anyone recommend adjustable weather stripping.

Gents, We're down-sizing to a condo with a asphalt floored garage. The blacktop is about 12-years old stained and dirty. I would like to power wash and seal with J-16 coal tar asphalt sealer. Looking for chemical resistance and ease in cleaning. Auto and boat projects will provide plenty of...

Got a simple single handle Moen bath faucet from HD and it is a piece of ****. Where can I buy the commercial stuff with the replacement cartridge, standard 3/4" aerator, etc. This is in a high use bath and I need a something that will last. Also, really digging that new brushed aluminum...

Just finished install last night. Have a box of maybe, 15-20 lbs of scrap of 1-color. Do the Racedeck folks want this back? Seems they can just throw in in the pot with the other graphite color when making new tile. Is it recyclable?

Gents, I'm remodeling my garage. Painting my 25-YO primed walls and ceiling. Ordering my Racedeck tomorrow. Cleaned up and painted my work bench and want to install one of those $89 Formica counter tops from Lowes. My top is 3/4" plywood with the outer plys being Masonite. It's had...

Just purchased this heater and since this is from China the regulator has the old POL tank fitting. Can't change the pig tail because the regulator is variable, that's how your regulate the heat. It does not not have a separate regulator, it's part of the tank fitting. So I need female POL to...

Some of my basement lights are wired through a GFI in my master bath 2-stories up in my house. Don't know why it's wired this way. When I switch on my work bench lights I sometimes trip the GFI. Do these wear out and become more sensitive? The lights on my bench are 2 X 4' T-12 Fluorescent...

It's been over a year. The Ladyship said all my designs were too Nascar. I said she can take here fung-schway BS and cram it. That was real productive so the project was shelved for a year. Finally compromised on a design. The Racedeck folks have been real patient with us. Getting ceiling...

Here on the East Coast we have huge swings in dew point and I occasionally get condensation on my garage floor. I'm torn between these systems and like them both but I'm concerned about how each would do with moisture. The syn fabric underlayment would be required with RD plastic tiles because...

For the home DIY guy don't think you can beat the HF swivel head ratchets. Problem is they don't sell them in a set. Does anyone know of a 3-pcs set, 1/4, 3/8 & 1/2 in padded or bare handles at the HF price?? Really on a tight budget.

Gents, On a tight budget and looking for inexpensive but quality pry bar set. I'll never have a need for anything over 24" so a 3-piece set should be fine. Problem is the spread in pricing from $10 for HF set up to $100's for a SO set. So can anyone recommend an inexpensive but decent quality...

Do you guys prefer the soft or hard handles and why?? Recall reading a post from a guy that swore the soft handles got softer with age. I can't afford to spend that kind of money and be disappointed 6-months later after I get brake fluid on a handle.

Looking for used sets. Seeing some used sets on ebay along with some used sets. Seems the sets hold their value when they are complete with the original case. I have no need for the case and looking for sets sans case. Are the new sets on ebay fakes? Some seem a little cheaper than off the...

The legs look like 3/16" angle. If I was close it'd be mine. http://www.ebay.com/itm/14-Drawer-Sears-Craftsman-Toolbox-Rolling-Cart-Shop-Cabinet-Table-Work-Bench-/121548124824?pt=LH_DefaultDomain_0&hash=item1c4cd53298

Not sure why but the change of seasons here in the North East causes my garage floor to sweat. Happens in the Spring and Fall. That said is my only option a vented plastic floor tile?

Really like the HF Red 5-drawer, but having sliding lids is really appealing. This cart is about $100 more and I'm willing to spend the extra money, but I've only found 2-reviews on Amazon. They are favorable but I'd like more feedback. Anyone have any experience with this cart? Do those...

Considering this cart. Can anyone advise the sized (depth of the drawers?) Spec says 20" but I think that is the outside dimension of the cart. Thanks

Anyone know who makes a set like this? I've seen SAE but not metric. I'm phasing out my 3/8" stuff; broken too many bolts with my ****-*******. Not a pro just wrench on the KTM, Harley, etc.

Just got my little stubbies with swivel heads. Not too bad for $8. Ratchet mechanism is a bit tight and can't see how they come apart. Any ideas how to lub it up to make it quieter and less binding? Little oil in through the socket release?

Just saw that thread about 1/4" deep wells. I thought I was the only one to use 1/4" drive almost eclusively. Yep, I've snapped my share of bolts from ****-******* a 3/8" ratchet. Problem with the 1/4" ratchets is I keep hitting the direction changer thingy. Looking for a 1/4", fine tooth...