Search results

Hello, I am looking for a Wifi thermostat that is able to control heat to 35 degrees F (40 could be OK but would really prefer 35) Application is the attached garage and the intent is to keep it slightly above freezing to allow the snow etc to melt off the cars. The attached garage is...

These have been picked up. Please delete. Hello, I was cleaning up the shop and realized I have a bunch of torch tips and bits that do not fit my current setup. Some bits are new in the box, some are used. If anyone wants it, let me know when you can pick it up and it is yours. I am in...

Hello, I would like to add 2 U shaped track lighting runs into my barn. The outer U will be about 32ft long, by 40ft across then 32ft back. (104ft total) The inner U will be the same 32ft long by about 12ft across. (76ft total). I would like about 10 - 20 LED spot type fixtures on each...

Bridgeport brand 15" rotary table. $195. Oily and could use a cleaning, but works fine. It is located in Milford, MI 48380. (Very close to GM's Proving Ground) It is heavy so I would prefer not to deal with shipping. Takes 2 strong people to pick it up. - Joe

I got these in a lot at an auction, but they are too large for my welder. Free to anyone that wants to pick them up. I am in Milford MI, right next to the GM Proving Ground. If you would like to come pick them up PM me your phone number and we can coordinate. Qty 7 Tweco Wc54-EL adapters Qty...

Decent job of controlling and accounting for variation. Surprising results...

I would like to add a solenoid valve to isolate my compressor from my shop piping when I am not in the shop. I would like the solenoid to be normally closed, open when it sees power. The power will be 24VAC from a CPT that I have hooked to my lighting circuit. I tried Grainger and all the...

This is a nice puller set, but the real deal is if you select the "front end service set bundle" which adds the on car press. (giant C clamp) Puller Set & on car press for $107.60 is a good deal, either retails for about $100 each. I couldn't figure out how to make the link go right to the...

I have several 8 ft T12 lights in my two buildings for a total of 44 single pin bulbs and 4 double pin HO bulbs. The magnetic ballasts hum, more light is always better. I looked into replacing the fixtures with tandem t8s, but I really don't feel like replacing all the fixtures. I am...

This is the best price I have seen on the Pro (18 gauge welded) upper cabinet. http://shopnewage.com/cabinets/pro-series/pro-series-18-gauge-fully-welded-wall-cabinet-in-grey.html -Joe

I have a cheapo GRIP partswasher that basically looks like this: http://www.harborfreight.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/i/m/image_22684.jpg It still works fine, but is looking kinda rough so I started thinking about getting a new one. Apparently all...

My barn tends to run on the humid side. It is particularly troubling in the early spring when the barn is still cold, and the air is warm and moist, but year round the humidity levels are high. I live in SE Michigan. It is a 44 x 54 building with a concrete slab. On top of the slab is a VCT...

I did a buy online pick up in store. Probably not the highest quality but at a buck each for a Lufkin, I will have one in every car. http://www.sears.com/lufkin-3pc-measuring-tape-set/p-00948058000P?sid=IAx20050830x000545&aff=Y&PID=4485850&AID=11034749

I have been considering buying a used floor machine. I found two that are potentially interesting and wanted to know the pros / cons. One is a used 2 speed 20" Clarke unit for $175. It looks well used, but owner says it works great. It is missing a drive pad, which is about $100. The...

If you happen to live near Milford Michigan, one of the local hardware stores, "Gilroy's Got it", has black Rubbermaid Roughneck indoor / outdoor garbage pails with lids on clearance for $2 a pail. These are good pails and are normally about fifteen bucks each. They are right in front of the...

Thanks to everyone's replies to my previous thread, I have committed to tile the floor in my barn. The area is about 23x29 (670 ft^2). Currently looks like this: These are the materials I plan on using, am I making any mistakes? Rent a diamond grinder to remove paint...

I am seriously considering laying porcelain tile in my workshop as a flooring material. I have read many posts, and done several searches, and all I find are success stories. Has anyone had a bad experience? If so please post details. I searched for a while and can not find one bad...

My vehicle storage barn Purchased a new home and did some work on the barn. Figured I might show it off here... Before: After:

I would like to add additional fluorescent lights to my barn. I would like them to hang down about 4 feet from the 12' ceiling to concentrate the light over an area I will add a workbench to. There are existing lights that are mounted directly to the ceiling and are fed via romex in the...