Search results

Hello, I have a 10x16 shed and I want to put a 6' door in the end/10' wide part. This is a portable building, and if fairly level. The question is: When adding jack and king studs, should I frame them plumb or measure off of adjacent studs to install?

Hello Happy Craftsman Block Grinder Parts Holders, I need one side cover for my grinder (I think the parts are the same for the left and right side) and two tool rests. I could also use some shields. Here are some pictures of what I have. The info sticker is completely faded except for 1/2...

I'm going to try to consolidate all of my Craftsman projects into one thread. I don't know how to go back and put my individual project threads into this one, but I hope someone can help me out with how to do it. Yesterday, The Craftsmans gathered for a family portrait. They did not comply...

I am planning to build a welding table using the base of an old Craftsman radial arm saw to put the top on. The top is 3/16 steel and the measurements are 26"x36" approximately. The table will be used in my home garage/workshop and I don't plan to have any huge projects. My welder is a...

Well, thanks to Lookn4'67Galaxieconv, I have a new top box. I got it the day before yesterday and have already begun the restoration. I've completed three of these so far, and also 3 rollers. I just recently finished the last roller I had so this was perfect timing. I am expecting a new lock...

This motor is going on an old Sears/Homart fan. The shaft rotates clockwise, but I need to reverse it in order for the fan to pull air out of the room. I don't know much about wiring at all! Please help. Thanks.

I hope some of you will be able to help me out. I'm putting in Allure Ultra Vinyl plank flooring over 3/4" tongue and groove sub flooring. One side of the room has dropped about an inch over the last 35 years, and I want to use Henry 555 or 565 self leveling compound. Does anyone have any...

I need the clamp/mount for a Craftsman 50's-60's band saw. It needs to be for a column mount. Here is a link to what I think the mount looks like. Thanks. https://www.picclickimg.com/d/l400/pict/282447402719_/Vintage-Sears-Craftsman-12-Band-Saw-10324280-Column.jpg

https://www.picclickimg.com/d/l400/pict/282447402719_/Vintage-Sears-Craftsman-12-Band-Saw-10324280-Column.jpg

I'll start by saying I'm not a welder by trade, and I'm a terrible welder as a hobbyist. I have only had my welder a few months. I'm making a cart from mostly junk that I had, or got at the scrapyard. The frame is from an old minibike, and I'd like to know if you have suggestions or comments...

I have been looking for a couple of these for a while now (mechanics and woodworkers). I got it Sunday, and it is now looking nice and matches my other CM red and gray cabinets, etc. I was in good shape, so I just sanded some, and got down to bare metal where there was rust.

I got this drill press free when I bought an old Craftsman scroll saw and sander. I am in the process of taking it apart to clean, and possible restore. Can anyone tell me how to get the pinion shaft out without messing anything up? Should I just leave it in? I also need to know how to get...

I believe I posted this somewhere, but photobukit killed my photos. I am going to paint it in the gray and red style to match my other Craftsman boxes/cabinets.

s1202.photobucket.com

This is my 3rd Craftsman roller. I was happy to find one that would be pretty easy to restore, since my second one has been painted with appliance paint, and won't be easy. I finished the two drawer chest that will go on top of this cabinet, at least until I find another 10 drawer. I sanded...

Special assistance needed in the.... Electrical Wiring Department. I am not very knowledgeable with wiring. I am trying to rewire my vintage Craftsman motor back to 110, and put in a switch. I see a wiring diagram on the motor, and on the switch itself, but I am clueless. Can someone give me...

I got this Craftsman welder today, and it is a beauty! Well, not really. It's pretty dang ugly, but pretty cool I think. I weighs a lot is about all I know about it, other than it's missing the leads, and plug. The gentleman I got it from told me that it belonged to his father. I plan to...

I need to replace the cords and stress relievers on two power tools. One is a Makita finishing sander model 9045B, the other is a Craftsman drill model number 315.271410. I want to order from one site, but when I find both in stock, one of the cords is about 9 bucks, and the other is about 36...

would it be a worthwhile addition to a vintage Craftsman drill press? I don't even know if it would fit...

https://img.letgo.com/images/aa/17/17/cd/aa1717cd215ee0f9010e2ecf36c39502.jpg