Search results

I bought a Sear caster kit 9-22221 for my Craftsman 113.29940 table saw. Of coarse the directions say for all Craftsman Power tool leg sets. When I went to install, the bolt holes will not line up. I am ready to drill new holes, but want to verify that the casters will support the weight. Its...

S-K 1/2" drive 11 piece socket set $20 Snap on nut drivers $45 Snap on Flare nut SAE wrenches $40 MAC metric flare nut wrenches (12/14, 11/13) $25 Easco 16mm combo wrench $5 Olympia 12" adjustable wrench $5 Snap on 12mm combo wrench $10 Blue Point 18mm ratcheting combo wrench $20 Proto 3/4"...

Snap-On 3/8, 7/16, 1/2, 9/16, and 5/8 open end flare wrench set. $65 plus shipping.

Im looking for a few yellow handle Snap-On nut drivers. I need 1/8, 5/32, 3/16, 7/32, and 5/16 SAE Also need 13mm-15mm Metric I have a few spares that I can trade as well. 11/32, 3/8, 7/16 and 1/2 . There is some rust within the handle on these. Also 8mm and a brand new 11mm to trade

My dad has an old round head Snap On torque wrench. He has taken the head apart to repair it and misplaced everything. Can the ratchet head be purchased without a handle? I will have to get a part number, but it is like this one of ebay...

I bought a Craftsman 113.29940 with SawStop fence and extentions. The blade will not set to 90*. More like 89*. I have adjusted the stops, but it was no help. I realised that the pulley is contacting the table. The pulley will only go so far and stops on the arbor. It the arbor tapered? Im...

A while back my old Speedaire compressor pump took a ****. The tank and motor are in good shape. I was digging around last week and realized I have a extra RV2 compressor from a 76 Valiant. Has anyone ever tried to fab a car compressor to a electric motor?

Im trying to find out the model of my Speedaire compressor. A few weeks ago it started leaking oil from the weep hole on the crank cover. I'm guessing the bearing has gone bad. I also heard that a bad check valve could give issues. I have never messed with a compressor other than turning it on...

Im needing a place to park my mowers and 56 Ford 600 tractor out of the rain. I picked up a bunck of corrogated steel to do cover 14' by 20' I also got 2 4x4 steel posts. The question is what do I use for the rafters and framing? A friend says pressure treated pine, while my uncle says go with...

My home is about 1600 sq ft and the attached garage is about 200. Yes, very small. I want to put central A/C to the garage. What size unit will I need to accomodate this space? Hopefully I can just plumb in a new vent or 2.

What to you use to tape and float hardi-plank? I'm doing interior walls.

Im going to run a 100amp sub-panel from the house. The electric company said 2 ot cable. I went to a local supply house and a electrician said to run 3 strans of #3 and one #6. The #2 was $881 for 3 runs at 150 ft. The #3/#6 was only $425, plus $60 for conduit. What is correct? Its a 150 ft run...

I have some left over floor stain and would like to put a big star on the floor. Whats the best way to get a clean line with stain?

Well, tomorrow I start to work on my shop. Its a unfinished 1500sqft shop. The PO didn't finish it before we bought it. I didn't have the spare money or time to finish the inside of the shop when we moved in. Thats going to all change now. I took 3 days off this week, plus the weekend to gut at...

I have a stainless steel butchers table. Would this work well for a welding table?

Do I have any options? My house is 1600sqft. And my shop is 1500sqft. What I have been told is that the shop is too big to run off the house, so the shop needs to get its own meter. Is that completely true? Could I upgrade the service to the house? Im a dummy with this stuff, but I want the most...

This is the plan for my shop. I know little about wiring. I got one of the HD books and read through it and decided to draw it up. Anyone see any big (or little) flaws in the lay out?

I was at Home Depot yesterday and they had the top section of the Husky pro box on clearance for $250. It looked like the 41" wide model. They didn't have any of the lower units

Can you recommend a good and cost effective battery chager for home use?

Where can I get a snap-on catalog? I went to snapon.com and tried to order one, but it requires a dealer name and I don't have a dealer.