Search results

I have Purchased a Sanborn 60 Gallon air compressor, which comes with a 755H pump, The intake air filter that it comes is pretty useless, has anyone modified it to accept a 1/2 NPT canister filter type? I would like to use a Filter Silencer Solberg FS-06-050 Filter Silencer, 1/2" MPT...

No, my compressor does not have a cooler, I was going to install this refrigerant dryer between the pump and tank Here are the Air dryer refrigerant specs; Inlet air temp. Temp: 100 (Max 120) Ambient temp. Temp: 100 (Max 104) Pressure drop: 0,15 PSI (Max 5 PSI) Pressure dew point: 33 – 39°F

I have a Brand New air compressor 60 Gallon 11.5 CFM @ 90 135 PSI Max I'm going to be using my compressor to paint car parts, from the little research I've done it seems the best way to eliminate any moisture in the air lines is to install an Refrigerant Air dryer between the Pump and...

anyone have any experience with these; Walter Surface Technologies 01E618 29-Piece Round Shank Jobber's Length SST Plus Drill Bit Set, Orange https://www.amazon.ca/dp/B00L59BRWU/?tag=atomicindus04-20

would these be a good set? does not say what material the bits are made out of https://www.amazon.ca/dp/B001C92C04/?tag=atomicindus04-20

I'm in the market for a quality set of drill bits, I will be using them to restore my car (broken bolts, sheet metal etc...) from the little research I did it seems like "Norseman" is a good brand made in USA, Just not sure what type to go with as there are so many to pick from if anyone...

I apricate all the replies, The more that I think about it I would like to use Copper as its easier to assemble and Acts as a cooler, with my design what diameter would you guy's recommend 1/2? or 3/4" Copper? Also I've updated my drawing, I will be installing rubber isolators on the...

is a aftercooler required?

i'm trying to eliminate any water in the line

I have just purchased a brand New 60 Gallon Sanborn air compressor, I’m going to be using this compressor to paint automotive parts for my car restoration. I need help planning out what is the best way to eliminate any moisture and water in the air lines, from the research I did it sounds like...

I'm looking at these two compressors; I think for my home garage that does not get used everyday either one of these should work, what do you guys think? and which one should I go with? Ingersoll Rand 60 Gallon Single Stage Air Compressor (SS5L5) 5HP, 240V AC 22.5 Amps Air Delivery @ 90 PSI ...

currently have a Pro air ii compressor 25 gallon oil free and for what I'm using it for its not big enough specs; - 5.3 CFM @ 90 PSI - 25 gallon tank - 120 Volt / 15 amps I'm looking for a oil stationary 240 volt Air compressor, It wont be used everyday but will be using it for the restoration...

Thanks for the reply, its hard to see from the pictures, did you use a Appliance connector to connect to the stainless or did you just connect the 45 degree elbow directly to the appliance?

Thanks for the reply, did you fasten it with screws and high temperature silicone ? What brand of stainless steel vent did you use ? And did you install a condensation drain in the vent system with the slope toward the unit heater as per vent manufacture instructions ?

how did you attach the Termination hood that is supplied in the reznor vent kit to the stainless steel pipe, there is no room for the gear clamp??

I have purchased a Reznor UDAS separate combustion unit heater along with there " Aesthetic Concentric vent kit" part # CC14 I need to install Category III vent pipe, all the stainless steel vent pipes manufactures use a O-ring and gear clamp to hold the joins together, how would I attach the...

I have a double car Garage (22' X 24') block construction. I would like to make the loft in my garage as a storage area. The ceiling joists are 5.5” High X 3” Wide X 24 Feet Long without a support in the middle (see pictures) and the spacing ranges from 31.5“ to 33” center to center. I'm going...

how many vents of 4" would I need to add?

Looking to insulate and properly vent my attic in the garage. The garage block construction with no insulation at all at the moment, the garage is 22' X 24' with a loft, I'm thinking completing the loft floor and placing insulation (R20) and vapor barrier under the loft floor. Also the soffit...