Search results

This roof is about 20 years old and started ******* up like this about 5 years ago. The plywood underneath looks good from the attic side. This is the north side, south side is fine. Does anybody have any ideas regarding whatmay have caused this and more importantly what I should do to correct it?

Year:2014 Make:Chevrolet Model:Cruze Mileage:207300 M Transmission:Automatic Engine:Diesel 2014 Cruze 2.0L TD 207,300 miles, garage kept, clean non- smoker & no kids. Reliable daily driver 100 mile highway daily commute for its entire life. Very clean inside and out except typical door dings...

The keys on my Radio shack remote keypad have gone wonky from years of use. I'd like to retrofit a keypad with RFID access. The current keypad is a 49-452, 4 wire. 2 terminals marked 12V, the other 2 marked SERIAL DATA. There's also a 2 switch DIP switch for addressing. Anyone made an upgrade...

I'll be replacing fuel lines on a 96 Buick Park Ave next week. What is the correct tool for this fuel fitting? Thanks in advance-

Is it possible to query KIAs to review when "maintenance required " messages were reset? Trying to fill in the blanks on a missing oil change entry in my service history.

I recently repaired a vertical shaft 8HP Briggs and Stratton, was burning oil when replaced 20 years ago. I needed the engine for a project, pulled it apart, cleaned all the carbon build up, lapped the valves and replaced the rings. Clean tank, new fuel/air filters and plug. Also replaced the...

Pulled this guy out of a drawer a few days ago. Not much info on C.E. Bonner Mfg and no mention I found of this piece. I can't make out the second line under the makers name.

Needed to do some digging last week and dug out this Greenlee #2 hand auger. There doesn't appear to be a "show us your vintage Greenlee Tools" thread. If I'm correct, I'll rename the thread and make one.

All new and unopened in the boxes. Raybestos P/Ns: Front rotors, 780964R Front pads, MGD1589CH Rear rotors, 780965R Rear pads, MGD1596CH $100.00 Local pick up in NW IN/ NE IL. Sent from my SM-G960U using The Garage Journal mobile app

I just got a new coil for my mower and the plug ends require some assembly. I've Googled and searched YouTube for guidance on this type but come up dry- any guidance from the Garage? Sent from my SM-G960U using The Garage Journal mobile app

I searched the mfgr lists but couldn't find a Cresent Tool thread. The marking reads: CRESENT TOOL CO JAMESTOWN NY USA M16 Sent from my SM-G960U using The Garage Journal mobile app

Does anyone recognize this electronic component? Its on the neutral side of a 1400W pannini press that until last night was working fine. The component reads open and when installed is attached to the bottom plate. Screwdriver is pointing at it in the picture. I'm guessing that its a one time...

This set sees a lot of use out in my barn. I added the 4060 ratchet because I didn't like the way the original 4501 is so easily reversed. Other than a broken deep 9/16 socket, it's complete. Sent from my SM-G960U using The Garage Journal mobile app

My Radio Shack model 49-485 alarm panel has lost its mind. The main keyboard randomly "loses it's mind", beeping an flashing. I've isolated zones but no change. Any recommendations for a replacement? Sent from my SM-G960U using The Garage Journal mobile app

I came across a 4L350R belt the other day and haven't been able to find a definitive answer as to what the R designates. From what Ive seen I'm guessing rubber. Thanks Sent from my SAMSUNG-SM-G930A using The Garage Journal mobile app

Does anyone have the ability to fax by way of a cell adapter such as the Huawei F256VW? Background: I live out in the country with terrible land lines. I eliminated land-line to my house several years ago with service thru Verizon using the F256VW fixed wireless terminal. It accepts the cell...

I've installed several remote grease lines to bearings on equipment but I've run into difficulty with pressed in zerks. I'd been running tubing and fittings to the threaded openings on the bearing housings but with the press in zerks I need something that snaps on to the zerk and can be piped...

Used, in good shape. Retracts and locks. No shipping, this ****** is heavy. 100.00 ~ located in Eastern Will County IL Sent from my SAMSUNG-SM-G930A using The Garage Journal mobile app

The fan motor on my late 70s heat pump unit is failing. I'm having some difficulty finding a replacement. GE part number 5KCP39PGD8318 3/4 hp, 1075 rpm, 200-230VAC. It's a 3 legged mount off the opposite end. Any help to point me towards a replacement would be appreciated! Sent from my...

Is it there? It took me a while to get the hang of taptalk so, it's quite possible I just don't see it due to my minor technical stupidity Sent from my SAMSUNG-SM-G930A using Tapatalk