Search results

I see a lot of posts about Rotary, Mohawk, Bendpack and others but everywhere I go in this area I see Challenger lifts. Is there just a REAL good salesman in this area for them or are they a good lift? A buddy of mine has had one in his shop for a lot of years without any problems that I know...

And now, for the rest of the story...the COA of SO rats As noted in the thread on the new Verdict, I just got back from the Snap-on convention in Florida. I had a great time, saw a lot of great tools and even had the pleasure of meeting Chad from here on GJ. I now know why he has very few...

Just got back from the Snap-on convention in Orlando (went down with my dealer) and had a great time except for one issue that will be in another thread. The one GREAT tool that I played with while I was there was the new Verdict diagnostic tool. For all of the Snap-on diagnostic tool guys out...

I was on the truck last week and saw this prybar and just could not resist this week. Reminds me of a Katana, it's stout, two handed and watch out for the end, it is WAY too sharp for a prybar. The edge is more like a wood chisel than a tool to pry with. If someone can bend this one, I don't...

Not mine but it looks like a fair deal if real.... Snap-on Top,bottom and side

Picked up a used Walker jack this morning and the gentleman I bought it from was going to "help" and top it off as he thought the fluid was "low".... Well, he snapped off the vent cap (didn't know it unscrewed) trying to pry it out. I hope they are still available. If not, I will make an...

OK, After buying the Wilton yesterday, I had an extra vise and knew that Dad wanted one sooooooooooo, I packed up the Record in the trunk and took it to him today. I knew that he wanted a small vise and that was the smallest of the three that I had. While I was there he wanted me to take his...

I think is is from the same guy that I bought my Brannick strut compressor from. If it is, this is out of a closed Goodyear store. Either way, it's a great deal IMO for $600. Hunter 4 wheel alignment machine

I bought an Accutire racing gauge a couple of years ago in because of the accuracy claims of the company and the warranty (5 years). The gauge is accurate to .1 psi and, until a week or so ago, it had been working out great other than the spring clip on the chuck breaking about a year ago (no...

I couldn't resist, they kept calling out to me from a guys basement... It included a complete set of Matco 3/8 short impact sockets from 10mm to 22mm, a SO 3/8 dr F723 push release, a SO 1/4 dr TL936, a SK 1/4 dr 40971, a couple of SO 3/8 dr bit sockets, a SO hard handel #2 Philips, Mac bit...

I have been wanting one of these for a long time as the "rentals" from the parts stores are a little lacking in safety (to me anyway) and I have almost pulled the trigger on a truck brand spring compressor a couple of times. Was looking over CL last night and an add caught my eye for 2 wall...

I'm looking to get a welder and it has been a LOT of years (25+) since I grabbed a stinger for anything other than tacking parts together. I don't need anything for production structural steel fab but just a nice little 220v mig to weld up trailer frames, lawnmower decks, car frames, sheet metal...

Any of you guys interested in a 208 pound Peter Wright anvil? A local seller has one listed for $250.00 on CL. I would like to have one but that joker is a little to much to lift...I'm still hunting for one a little lighter. Used anvil for sale

I have been thinking about getting a TIG setup and know of a Miller 250 Syncrowave for sale with a built in liquid cooler for the torch ( I am assuming a Coolmate 3X) but without the bottle for $2,800. That seems a little high for a used one but thought I would ask the experts here what they...

If any of the Snap-on dealers on this board know how to find the dealer in this area of Georgia, you might want to make them aware of this. Sounds like a new purchase trying to sell and skip. No way will someone sell a new box and never used tools for this cheap. Cheap Snap-on No way in hell...

Found some over the top air receivers that would fit into OCG's shop and look right at home... Anyone out there need some extra air on occasion? "small" air tanks in north Georgia

I know that a bunch of you have bad ones but thought I would give out some good news for a change. First up was the MAC truck guy. I have never met the man before but have seen him driving around the area. I had one of my old flex head ratchets that needed a new screw (the old one broke in...

Not mine but $1,600 for a Rotary lift doesn't seem to bad. If you live in Georgia or north Florida, it might be worth the drive. Used 7000# Rotary lift

When did Snap-on start making these with the fake Carbon Fiber cover? My Snap-on guy said they were only available at the Vegas show this year. Either way, it comes pre-loaded with 9.4 and I like the looks a lot more than the plain red version.

Not mine but I hope a fellow GJ member can get to this one. An almost new (60 days old) KRL1022 for $900.00. He also has a couple of other boxes. Black KRL 1022 for sale