Search results

  1. 1

    Sanborn Air Compressor 755H pump Intake Filter mod?

    I have Purchased a Sanborn 60 Gallon air compressor, which comes with a 755H pump, The intake air filter that it comes is pretty useless, has anyone modified it to accept a 1/2 NPT canister filter type? I would like to use a Filter Silencer Solberg FS-06-050 Filter Silencer, 1/2" MPT...
  2. 1

    Refrigerant Air Dryer for Air compressor

    I have a Brand New air compressor 60 Gallon 11.5 CFM @ 90 135 PSI Max I'm going to be using my compressor to paint car parts, from the little research I've done it seems the best way to eliminate any moisture in the air lines is to install an Refrigerant Air dryer between the Pump and...
  3. 1

    Drill bit set recommendations

    I'm in the market for a quality set of drill bits, I will be using them to restore my car (broken bolts, sheet metal etc...) from the little research I did it seems like "Norseman" is a good brand made in USA, Just not sure what type to go with as there are so many to pick from if anyone...
  4. 1

    Air compressor - plumbing and Aftercooler

    I have just purchased a brand New 60 Gallon Sanborn air compressor, I’m going to be using this compressor to paint automotive parts for my car restoration. I need help planning out what is the best way to eliminate any moisture and water in the air lines, from the research I did it sounds like...
  5. 1

    Air compressor

    currently have a Pro air ii compressor 25 gallon oil free and for what I'm using it for its not big enough specs; - 5.3 CFM @ 90 PSI - 25 gallon tank - 120 Volt / 15 amps I'm looking for a oil stationary 240 volt Air compressor, It wont be used everyday but will be using it for the restoration...
  6. 1

    Reznor UDAS Unit Heater and vent Kit

    I have purchased a Reznor UDAS separate combustion unit heater along with there " Aesthetic Concentric vent kit" part # CC14 I need to install Category III vent pipe, all the stainless steel vent pipes manufactures use a O-ring and gear clamp to hold the joins together, how would I attach the...
  7. 1

    Support Garage Ceiling floor

    I have a double car Garage (22' X 24') block construction. I would like to make the loft in my garage as a storage area. The ceiling joists are 5.5” High X 3” Wide X 24 Feet Long without a support in the middle (see pictures) and the spacing ranges from 31.5“ to 33” center to center. I'm going...
  8. 1

    Garage insulation / attic venting

    Looking to insulate and properly vent my attic in the garage. The garage block construction with no insulation at all at the moment, the garage is 22' X 24' with a loft, I'm thinking completing the loft floor and placing insulation (R20) and vapor barrier under the loft floor. Also the soffit...
  9. 1

    Garage Heater

    I'm looking for a heater for my garage its 24'X22' ( 528 Square feet) , the garage is not insulated and not sure if I should go with a mobile propane heater or natural gas heater, I will only be using the heater when I'm working inside the garage. It gets pretty cold here any suggestions
  10. 1

    Garage Door Finish

    Finally got around to stripping the garage door, It was a lot more work then I anticipated, I still have some more stripping / sanding to do. What stain do you guys recommend, I would like something that will hold up to the elements (we get a fair amount of snow up here) , I can't see myself...
  11. 1

    Garage Door Paint Stripping

    I need to strip my Wood garage door, originally it was varnished (I think) but someone has painted over the varnish and in some areas the paint is separating from the varnish (especially top of door) what is the best way to strip this door down to bare wood?
  12. 1

    Dewalt 20V MAX* XR (Brushless) 3/8" Compact Impact Wrench Kit (4.0 Ah)

    I'm looking at purchasing the Dewalt 20V MAX* XR (Brushless) 3/8" Compact Impact Wrench Kit (4.0 Ah). anyone use this daily on here? I'm looking to purchase this kit for work, I'm going to be using this to disassemble components ( example; transmissions, differentials, engines, torque...
  13. 1

    Air compressor air dryer Recommendations

    I have a Pro Air II by Devilbiss 25 Gallon 135 PSI oil free Air compressor, I get lots of water coming out of the air line. I'm going to be assembling an engine and going to be painting it and don't want water all over my engine, any recommendations for air dryer for this air compressor? Thanks
  14. 1

    Snap On Emblem

    I have a Snap on KRL 761 & KRL 791 tool box, I would like to remove the snap on emblems to take off the vinyl wrap, any idea how to remove the emblems without damaging them, there is 3 studs on the backside
  15. 1

    Air Compressor Problem

    I have Pro Air II by Devilbiss Air compressor, its about 14-16 years old but does not have much use on it, I've always used it on a 15 amp breaker and never tripped the breaker. Well now using the same outlet the compressor will start up and after a 1 minute of filling up it will trip the...
  16. 1

    Adjustable Wrench

    I need a 18" or so adjustable wrench for work, what brand you guys recommend
  17. 1

    Drill Bit Brand identification

    I was given these drill bits but not sure what brand they are, anyone know?
  18. 1

    Snap On KRA4107 Rubber Mat

    I bought a Used Snap On KRA4107 & KRA4114 and I'm missing the Rubber matt that goes in-between the two boxes. Snap On wants $45 for the rubber mat which is nuts. Anyone where I can get one cheaper or any specs on how thick this mat is and maybe I can buy a Mat at home depot and make my own...
  19. 1

    Air tools Recommendation

    I'm starting out in the Heavy Equipment trade and its time to purchase tools, What do you guy's recommend for air tools, I can get a discount with MAC tools & Matco. I've also done some research on AirCat there seems to be some good reviews and prices seems reasonable, what do you guys think?
  20. 1

    Sunex Jumbo Combination Wrench Set

    Anyone own Sunex #9707 Jumbo Fractional Combination Wrench Set, 7-Piece set, how is there quality, will they hold up for everyday use? I know they made offshore but are these comparable to Harbor Freight?? are they guaranteed for life? I was told Mac tools sells these off the truck...
Top Bottom