Search results

Are Snap-On FV series 12 point 3/8" sockets Flank Drive? Thanks!!

I want to understand using my Snap-On Super 550 Battery charger more. If I check the voltage across my battery with a digital multi-meter what should the voltage be? My charger book says 12.6V but my load tester book says 12.4V? My charger has 3 knobs. I understand the timer one. The...

Are the older FV series Snap-On sockets Flank drive??

Hooking up battery tenders (24/7/365) won't work out for me so I am looking for a small automatic battery charger that I can take to each battery . I want to top off the charge of each battery say every month. Any good ones? Thanks!!

Where and what make of replacement battery should I get for my JNC 950? Thanks!!

I was wondering what is the difference between a F140, FV141 and f141 Socket? I know that the F140 is the oldest and non Flank Drive. Thanks!

After Christmas I want to treat my self to something. I was wondering what would be the best in 3/8" size for under the hood work? I am thinking either the new Snap-On Cordless 3/8" Ratchet or the Milwaukee 2454-22 to supplement my Snap-On 4410. Or maybe just upgrade my Snap-On 4410 to a 8810...

I don't use my 3/4" drive sockets much but when I need them, I need them. I want to get some metric ones and noticed that some of my SAE sockets also have the metric size on them as well. Because I won't use them much and don't have that much room in my 3/4" drawer, I only want to buy the...

I am thinking of getting some Snap-On Spark plug sockets and don't know what type to buy, either the standard ones or the Retention ones. What are the Pros and Cons of each?? Thanks!

I have some questions on my Snap-On YA 700 jack rebuild. I nicked the seat (under the copper washer) getting the copper washer out of the pressure and suction valve screw. Can I just put a dab of RTV or The right stuff to fill it in? How tight do you make the big tank nut? I don't want to...

I am in the process of taking my Snap-On YA 700 apart and am thinking about assembly and have some questions. On the Hyd. pump assembly chevron seals, how tight do I make that little nut that holds them in place? I am thinking that the tighter I tighten the nut, the more the seals expand...

I have taken apart my Snap-On YA-700 hydraulic unit . The plastic guide is firmly stuck in the cylinder. It got pressed in by the piston and metal washer falling off and turning sideways. I am thinking to use a 1"bolt and screw it into the plastic guide then pull the bolt out. Any better ideas?

I need to soak my Holley Carb (Made in 1979). I am taking it apart. I have some Napa carb dip+basket that is probably 7-8 years old. How long should I soak my carb? The can says 10-15 minutes but I don't think that will be enough. Thanks!!

My Snap-On YA-700 jack will only go up 1 inch. I used it today, it wouldn't go up so I jacked it a few times then jacked up a car to full height. 10minutes later it only will go up 1 inch. I can stand on the saddle and it holds my weight then I turn the handle and it drops fine. The jack...

My POS Kenmore died so I need to buy a new dehumidifier, 25 to 35 pint size with no pump. Any recommendations? I see Grainger has a Dayton for $300, is that brand any good? Thanks!!

My wife has a Dyson DC 07 vacuum and it doesn't pick up like it use to. I changed out the filter and cleaned out the canister and it is only a little better. My wife read online that after a while, they get like that. Any ideas on how I can fix ours? It wasn't cheap when she bought it and I...

The battery for my 18 volt snap-On Cordless Impact wrench (3850) finally died. The battery is a CTB3185. Snap-On has them for $160, I can get a newer style /adaptor for a little less or I was thinking that my battery could be rebuilt. Has anyone had a Snap-On CTB 3185 ever rebuilt? Had...

What grease should I use to grease my Snap-On Right Angle die grinders like a Snap-On PT 210 or Bluepoint AT 109? Also, can I use that same grease to grease my Blue-Point AT 811 Right angle air drill? Thanks!

Does anyone make 7/32", 9/32" and 11/32" 1/4" drive impact sockets in shallow and deep? Thanks!

I am thinking of getting some more Snap-On Die Grinders. I need some info . I currently have a Blue-Point angle head AT 110 and Snap-On PT 200 that I have had for years. I was thinking of replacing the angle head Blue-Point AT 110 with a Sanp-On PT 210A or should I get the PT 410? Are the...