Search results

I have a nice Milwaukee The Hatchett cordless sawzall Unfortunately it uses the older M18 nicad pack and the batteries dont last long Is there an adapter that I can use my M18 liuthim batteries with the sawzall?

Auto Parts for the following: BUICK ENCLAVE 2008-2017 CHEVROLET TRAVERSE 2009-2017 GMC ACADIA 2007-2017 SATURN OUTLOOK 2007-2010 (2) “O.E. Brand” Ball Joints; $25 pair # DM15.4500088; Replaces MOOG K500088 (2) “Auto Parts” Tie Rod Ends; $22 each # 2600-258844 # ES800286 (2) “Auto Parts”...

Trying to figure out what to do with humidity/moisture in my bathroom I have a NuTone exhaust fan rated for 80 CFM My bathroom is 11' x 8' with 8' ceilings According to online calculators, I need atleast 93 CFM in this room I guess the contactor installed what he had? Code issue? Anyways...

Selling as ONE package deal $1,000!! Price is OBO! Send me an offer The lever control valves alone sell for $550 EACH, and I have three (3) Parker ½” reverse flow regulator; P/N # P32RA94RNGP (2) Parker 3/8” Compact Regulator; P/N # R11-03C/M3 (6) Mounting Brackets; P/N # P3NKA00MW (13)...

Trying to remove (un-thread) a metal plumbing fitting (basically a straight 4" long ******) Likely has been install on the house since the 1950s.........any tips or tricks? Have been spraying it with penetrant for a few days, wont budge. I was thinking about some heat with a small propane or...

Today picked up this little 120V, oil lubricated, portable air compressor When I try to turn it on, there is just a loud humming/buzzing noise The motor does not seem to turn on The compressor is probably 5-8 years old and appears to visually be in good working order What can I check to try...

So.............I have 3 nice shovels in my garage and the scrapers (edge scraper, wear guards, etc) ALL need replacing I was looking online and new shovels, like the three I have, are $30ish each The shovels themselves are all plastic, but the scrapers/blade edges are all metal.........just...

I have 6 roof vents and I would like to somehow temporarily add a poly square or insulation over them .......to attempt to loose less heat in the shop this winter Any ideas?

I would like to seal my PT pool deck before it gets too cold out I do not want a stain but rather a clear seal Recommendations? Also, can it be sprayed on or should it be brushed and/or rolled on?

Anyone have experience with fireplace log sets? I have an unknown age log set in my fireplace and I just removed it.......in order to shop for a newer updated unit. It never worked 100% and I really like the newer versions with the remote and flame adjust controls I have: -Natural Gas -Fully...

Anyone have ideas for storing rubber mallets on the wall? Looking to make or buy a hanger rack for a 4 or 5 piece set Thanks

So, I have been in my house for 5 years now...……..I have a 3 switch panel in the foyer, near the front door One switch controls the outside porch and garage lights One switch controls the foyer light and hallway light What could the third switch control!?! I have an outlet near the front...

So, I purchased an Ez-Go 48v golf cart for cheap...……….trying to see what I can do, if anything, to save the batteries It was completed dead and I had to trailer it home I removed all four batteries (heavy as sin!) and opened the battery maintenance ports, to find little (if any) water inside...

I was given a "Broken" Generac 01676-02 pressure washer Briggs 6.5 HP OHV Intek 206 CC 2700 PSI Came with the wand, hose, and a 6 piece nozzle spray kit I took the carb off and cleaned it...…...fresh gas and it fired right up The PO said it leaked oil...….and once a water hose is hooked up...

I am in the process of connecting some wiring for my pool pump (Hayward MaxFlo 1.5HP 2 Speed) The previous owners already had the wiring ran from the house to a "stub" in the yard. I installed a junction box and will be installing 4 outdoor rated GCFI outlets (all are 15A). Two outlets at this...

I bought this rolling box on CL for $100 years and years ago...…. Locking 3 digit, push button code roller. All drawers are ball bearing and the casters are 6"x2" and are greaseable Anyways, for some unknown reason ALL the drawers locked and I cannot open any. I also do not know the model...

I bought a used Troy Bilt generator for $100...……..missing some parts and trying to find them Troy Bilt Model "030248" REV "02" 3,550 W / 5,250 W Generator Powered by a Briggs & Stratton 7 HP OHV motor I am looking for the part number for the air filter and the part number for the air filter...

Anyone have the Diablo line of air Hose? Good or bad?

A drawer on my kitchen cabinet seemed to be sticking Looked underneath and this plastic spring clip was broke Any help with a link to find a replacement part? "Quality Cabinets" appears to be the cabinet brand THANKS! Broken side: How it is supposed to look:

What's GJ say?