Search results

We are in the process of buying a new home. Shop is 100ft or so from the house. Need to have internet in the shop and curious what the best /easiest way to get it out there will be. Previous owners said they already have a landline out there. We plan on goin with CenturyLink as a supplier...

Were in the process of buying a new home. Thinking of buying a paint sprayer. We are wanting to paint the kitchen cabinets and trim. Was hoping to stay under $250. Any recommendations or things to watch out for in a sprayer. Never used one before

What would be the easiest and cheapest way to get audio from my tv to my stereo reciever on the opposite side of my shed. Dont really want to run cables 50ft Didnt know if there was a cheap way to send signal wirelessly but not break the bank Sent from my SM-G930R4 using Tapatalk

So the pipe from the left comes from the CLOTHESwasher. We get a sewer smell up the sink when the washer runs. Do I need to add a trap below the sink also. EDIT: This is for a clothes washer Sent from my SM-G930R4 using Tapatalk

So strange request. I'm looking for a pheasant [rooster] walking silhouette dxf file. We have a lazer at work I'm looking to get a few cutouts on if I can find them. I've found a few flying mallards and they turned out great cuz cant seem to find and walking roosters. Thanks in advance Sent...

Anyone else using a big Maxx heater got mine hooked up now when it tries to come up to heat it runs for awhile then shuts off then runs for awhile then shuts off didn't know if it should be a continuous heat till it hits its set temp or if it should cycle like that. The fan motor continuously...

Just hooked up heater in shed and it wont shut off when it gets to temp that is set on thermostat. Assuming i wired it wrong Sent from my SM-G930R4 using Tapatalk

So I would like to add a second motion light on the front of my pole building. I have steel on the exterior and the inside is finished. Attic is not insulated yet so wiring wont be bad. My problem is that the light I already have is mounted on something similar to this.... and I'm have a hard...

So I tore out the old shower which consisted of 1in tiles on the concrete and this was the drain. What will be the easiest/best way if I want to put a shower pan in. Sent from my SM-G930R4 using Tapatalk

So we have tiled our main bath/shower stall ourself, we are wanting to do our secondary shower in our basement. Right now it has flimsy plastic/fiberglasss board on walls and ceiling over top of cinder block. (For the walls). This bathroom is in the center of the house, all interior walls. my...

So our house is a split foyer, 6 steps up....6 down. We are debating about adding stairwell lighting. Not sure if we want to do just 2 lights on the landing or a few on each section of steps. Definitely dont want one for each step. Anyone have any recommendations for the lights themselves...

Finally getting tired of working in the cold and need a real heater. Wanted to go the radiant tube heater route but cant afford it. Started looking at the hanging furnace route.my pole building is 30x40x10. Wrapped with tyvek and R25 throughout .no concrete insulation other then vapor barrier...

Anyone know of a legit site that wont break the bank, to order raised panel oak cabinet doors from. Tried at menards and they do not cary size i need. (16x34) i would nerr 8 of them Sent from my SM-G930R4 using Tapatalk

So i have a few gaps in in my osb walls/ceiling in my pole building. Example. Along overhead door framing or where wall/ceiling meet.....not the seams. Is there a colored caulk that is close to /doesnt look bad with osb. I dont plan on painting the sheets so i was hoping to get as close as...

Has anyone used a mounting block similar to this for mounting an exterior motion light their pole building with raised ribs. Sent from my SM-G930R4 using Tapatalk

I had a service tech come out for preventive maintenance. I saw him put a yellow "cough drop" looking thing by the the A Coil. What would that have been? Sent from my SM-G930R4 using Tapatalk

This winter I moves my thermostat and ran new wire to the furnace. Didnt have a problem all winter. . . Now we are to AC we have a problem and Air conditioner wont run. Worked fine before I reran wire. Assuming I'm missing something obvious Sent from my SM-G930R4 using Tapatalk

Long shot here. Has anyone built a sleeve hitch for a garden tractor. I'm debating on one for my john deere x475. Just not sure I would use it enough to justify buying a pre fab one. Sent from my SM-G930R4 using Tapatalk

Under my steel I have tyvek. Then I went with unfaced fiberglass due to the great deal I got on it...... am I goin to want to hang plastic next before sheeting it or with that cause moisture buildup in the walls Sent from my SM-G930R4 using Tapatalk

Just realized it was posted to the electrical section Sent from my SM-G930R4 using Tapatalk