Search results

which one works better? I have been using blue loctite for many years. found something recently name vibratite VC3. Supposed to do the same thing as loctite, but can be removed and moved as needed. So is this Vibra tite stuff as good as they advertise?

Gonna splurge and buy a nice tire plugging kit. Seems the 2 most highly rated are the Blackjack ones and Safety Seal. So which one should I get ?

if you were going to get a cordless 4 tool set, what would you pick to be in it?? Drill? impact? other?

http://seattle.craigslist.org/tac/tls/3953689409.html

One of the much wanted things I would like to have is a tire machine and balancer. I know they are expensive, but i would try to offset it by doing peoples tires. So anyone have a set at home?? was it worth the cost and do you use it often?

my vise has serrated jaws. I wish to use it for adjusting and installing pistol sights. Of course i prefer the slide not to have teeth marks on them, so what does GJ recommend for non marking jaws?

looks to be a HW. If i did not have 3 jacks already, i would be all over it http://seattle.craigslist.org/tac/tls/3958767591.html

Since the ex wife ended up with the house and kids, they are in need of a air compressor to fill tires. No tool use or painting. I have been looking at the HF ones and the reviews have been not too good. I am looking for something under $75 Any suggestions?

i am planning to build a new table for the garage. it will be used for reloading and firearms related work. I will be using 3/4 plywood as the base. i have some extra laminate flooring and i was thinking it might make a good surface to put over the plywood. its hard, replaceable and cheap. So...

reel mowers here is a machine for sale http://seattle.craigslist.org/oly/atq/3811053036.html

i was reading that the best way to adjust a 2 cycle engine is with a tach. i see non contact tachs on ebay. So how do they work? how does it measure on a 2 cycle engine?

i have my compressor apart now. the motor and pump are oily. i would like to spray some degreaser and wash them. will this hurt the electric motor??

so while i am livign at moms, i thought i would fix her house up a little. she is need of a garage door opener to replace the 30 years old one she has in there now. Still works,but remotes are hard to find and not safety features. its only a single 7x9 door. So I went shopping for a new...

make a diffrence??? I was getting my lawn mower ready for the season and I needed to sharpen the blade. My mower have a big center nut 24mm. i was lazy and grabbed a 12 point 24mm regular socket and installed it on my gun. I tried banging it off, but it would not move. tried it for a while...

i am looking for a used one. besides spraying some paint, how do it test it if i am at someones house checking it out?

i have a 30 gallon horizontal compressor. When it cycles, the vibration causes it to move around. Right now there are no rubber feet on the bottom of the bracket. Before i go to the trouble of grabbing some, if i do install them, will it fix the moving?

local craigslist ad. this seller seems to be asking quite a bit for it. Is it worth this much?? and its not my ad http://seattle.craigslist.org/skc/tls/3650869027.html

taking apart my compressor to move it. i need buy some pullers to pull the pulleys off. probably a HF one. the large pulley, does it need a special puller, or will a regular puller work?

i have a 80 galllon upright. i will be moving to a new home soon. when i got it, i had access to a cube ban with a ramp. unfortunately that is not the case now. So what would be the easiest and least expensive to move it? rent a truck and dolly? rent one with a liftgate? have a freind with a...

looks huge http://seattle.craigslist.org/sno/tld/3667457036.html