Search results

I have an older model Snap-On sand blast cabinet, and the gloves were bad when I got it. I did buy a pair of gloves from TIP in Ohio, but they are too big for the opening, and I am not certain if I should try to cut them down, or try to find the correct gloves for it. I am also missing the...

I found a used Hein Werner 2 ton jack, that the seller says has very little use on it, since he is a homeowner. Wants me to make him an offer on this. I am thinking about $100, but don't know if I am being realistic or not. My old Hein Werner WS is very tired and needs a total rebuild...

It is time to change the oil in my compressor, since it has been in there for a long time. I got the replacement oil and filter directly from the Quincy dealer, so I know that I have the correct weight. My question is... Should I run the compressor so the oil will be hot when I drain it, or is...

I picked up a Hein-Werner Model WS jack at the Stafford Springs swap meet this past Sunday, and as expected, it wasn't working. Can't expect much when you pay $5 for a rolling floor jack. Today, I had some time to start to check it out, and since it didn't raise, I started by removing what I...

Today, I learned about a Dale Earnhart box that is for sale. I haven't seen it, and I don't have the part number, but the price is extremely reasonable for a Snappy box. It is approximately 6' high, and 4' wide, and one solid piece. Does this help you to give me a picture of a similar box...

I want to replace my standard type of garage door operator with a Liftmaster 3800. There are 2 doors involved in this change over... one is a 10' x 10' insulated metal door that presently has a 1/2 HP Liftmaster track opener, and the other is a 9' x 8' also with a 1/2 HP Liftmaster track...

I ahve a Blue Point impact gun that has stopped working. I have a feeling that it rusted up inside because it hasn't been used in many years. It is a AT500D, that is no longer serviced by Snap On. Any suggestions what to do to revive this gun? It doesn't have a lot of use on it, but it is...

Looking for a reasonably priced Snap On Pitman Arm Puller for a full sized 1962 Chevrolet. Will also consider OTC.. thanks

I have an over abundance of Snap On tools that I will never need. I would like to sell them, and I have no problem piecing them out, however, I just don't know how to price them. Most are used, are not marked, nor are they shelf worn. Can you give me a general idea of how to determine the...

This is a NOS antique AC Spark Plug tachometer. It is complete except for the tip for flat surfaces, which is just a piece of rubber hose. Type 1, 0 - 4000 RPM. Asking $150 including shipping or a reasonable offer.

looking for OXIM10B & OXIM14B midget metric snap on wrenches. Thanks Junk..

I came across my old Snap On Tach / Dwell meter that hasn't been used in more years that I can remember. It is a model MT414. When I opened it, I found that the batteries had corroded, and considering that they are about 40 years old, it is no wonder. What would you suggest that I use to...

When buying a tool, such as a Snap On ratchet, do you value a new tool more than a excellent condition used tool? I see a lot of Snap On tools on ebay that are selling in the same price range as similar tools on these forums. I would prefer to support a forum member whenever possible, but most...

My Quincy pressure oil lubed compressor is located in a cold garage. What are your thoughts about starting it up to fill the tank with air? I have a slow leak on one of my tractor tires, and I have to air it up every snow storm. I would replace the tire, but it is on backorder from the...

Looking for OEXL wrenches to fill in missing ones. OEXL12 ... 3/8" OEXL14... 7/16" OEXL26 ... 13/16"...........Found OEXL28 ... 7/8"...........Found OEXL30 ... 15/16" OEXL32 ... 1" If possible, I would prefer with the old script logo, and on the reverse side to have it marked OEXL ** USA PAT...

Don't know what it is........... then watch this video..

I have been using a shop vac for years now, and I would like to upgrade to a real pellet stove vacuum. Any suggestions as to what is the best one to buy? I looked at the one at Tractor Supply, but it was not very well made, and just by looking at it, I could tell that the filter will clog...

I have a 20 year old Harmon Pellet Stove that started to just continually spew out pellets, since the pellet auger motor will no longer stop turning. I did a goggle search for troubleshooting, but came up with nothing. I hate the thought of trying to find someone local to repair this, because...

Ponder this about Sears....... Amazing when you think of how long the war has lasted and they haven't withdrawn from their commitment. Could we each buy at least one thing at Sears this year? How does Sears treat its employees who are called up for military duty? By law, they...